0
"Try gun shops, gun shows, pawn shops, want ads"- rebuttle: this is an extremely hard part to find. It would not be at any of those places (with the exception of maybe a random gun show) ; could people only answer the question if they actually know where to get it? I.E. you've seen one for sale somewhere!
What else can I help you with?
How do you remove the magazine tube from a Remington 1100?
To remove the magazine tube from a Remington 1100, first ensure the firearm is unloaded and the action is open. Then, unscrew the magazine cap located at the end of the magazine tube. Once the cap is removed, you can slide the magazine tube off the receiver by pulling it forward. If necessary, gently tap the tube to loosen it if it's stuck.
How do you remove the magazine tube on a 870 Remington shotgun?
The actual magazine tube that connects to the receiver is brazed in there, so it removing it isn't an optimum solution.
Can you replace a magazine tube on a Remington auto 3 model 11 the sportsman and make it an auto 5?
No
How do you increase the magazine capacity of a shotgun?
Pump and some autoloading shotguns of popular makes with tube magazines using threaded magazine caps can have magazine extension tubes added. Typically these are sold as a kit with tube and spring. The tube replaces the magazine cap. Box magazine shotguns such as the Saiga just need a larger capacity magazine added. Older shotguns using magazine plugs held in by screws usually cannot increase mag capacity.
How do you load a 22 cal magazine tube?
Depends on how it's set up. In a traditional configuration, where the tubular magazine is under the barrel, there'll typically be a cap at the end of the magazine. Rotate it counterclockwise, and pull it out. Attached to it will be a long tube and the magazine spring, and this action will open the magazine for reloading. On some rifles, such as the tubular mag fed versions of the Remington Nylon 66, the magazine inserts into the back of the buttstock. You will again need to rotate the latch counterclockwise until it unlocks, then remove the magazine.
How do you remove the forestock on an 870 Remington shotgun?
Unscrew the magazine tube cap, pull the barrel off to the front, remove the forestock. If in doubt, consult the owner's manual. A replacement owners manual is available through Remington's web page.
How do you insert a plug for a Remington 870 shotgun?
On the end of the magazine tube there is a threaded-on cap. Remove this cap. You will now find a "spring plug" inside the front end of the magazine tube. Carefully pry this spring plug out of the magazine tube. Put a pair of safety glasses in the proper location on your face because once you get this spring cap close to the end of the magazine tube the magazine follwer spring will push it out of the mag. tube faster than you can say"Oh sh.. crap". Once this spring cap is out you can pull the magazine spring out if it already hasn't landed in the living room. You can now insert or remove a cartridge number restricting plug. Next you'll need to push the extended magazine spring back into the magazine tube and re-install the spring end cap. To get the spring plug in flush with the front edge of the magazine tube, tap it into place with a plastic screwdriver handle to prevent distorting the thin walls of the mag. tube. Replace the screw-on end cap and that's it.
Will a magazine extension for a Winchester 1200 shotgun work with a Winchester 1300 shotgun?
No, a magazine extension for a Winchester 1200 shotgun will not work with a Winchester 1300 shotgun. The Winchester 1200 and 1300 have different magazine tube designs and dimensions, so they are not interchangeable.
What is the difference between a Remington nylon model 11 model 12 and model 66?
The model 11 is a bolt action clip, the model 12 is a bolt action magazine tube, and the model 66 is a autoloader (also a magazine tube). The 11 and 12 were made from 62-65 the 66 was made from 59-89.
How do you remove magazine tube on Stevens 87d?
To remove the magazine tube on the Stevens 87D, first ensure the firearm is unloaded. Then, unscrew the end cap at the front of the magazine tube. Slide off the end cap and follower, then push the magazine spring and follower out through the rear of the tube. Finally, slide the magazine tube out of the receiver.
How do you take the plug out of a Remington 1100?
Remove the magazine cap and forearm, then remove the barrel and mag tube. At the end of the tube will be a metal cap that you can carefully pry out with a screwdriver, some press in and turn to remove them. Use caution, it is under spring pressure.
Can you convert your 22 tube magazine to a box magazine?
No
