answersLogoWhite

0

The actual magazine tube that connects to the receiver is brazed in there, so it removing it isn't an optimum solution.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How do you remove the magazine tube from a Remington 1100?

To remove the magazine tube from a Remington 1100, first ensure the firearm is unloaded and the action is open. Then, unscrew the magazine cap located at the end of the magazine tube. Once the cap is removed, you can slide the magazine tube off the receiver by pulling it forward. If necessary, gently tap the tube to loosen it if it's stuck.


How do you remove the forestock on an 870 Remington shotgun?

Unscrew the magazine tube cap, pull the barrel off to the front, remove the forestock. If in doubt, consult the owner's manual. A replacement owners manual is available through Remington's web page.


How do you remove the magazine tube from Charles daly 20 gauge shotgun?

To remove the magazine tube from a Charles Daly 20 gauge shotgun, first ensure the firearm is unloaded and the action is open. Locate the magazine cap at the end of the magazine tube, unscrew it counterclockwise, and then carefully slide the magazine tube out of the receiver. Depending on the model, you may need to remove additional components, such as the forend or any retaining screws, to fully detach the tube. Always refer to the specific owner's manual for detailed instructions related to your shotgun model.


How do you remove the plug on a Winchester ranger shotgun?

To remove the plug from a Winchester Ranger shotgun, first ensure the shotgun is unloaded and pointed in a safe direction. Then, locate the plug inside the magazine tube, usually accessible by unscrewing the end cap or the magazine cap. Once the cap is removed, you can slide the plug out from the magazine tube. Reassemble the shotgun by securely replacing the cap.


How do you remove the magazine tube from a Browning Gold 10G shotgun?

Best left to a trained gunsmith


How do you remove plug from Remington 870 shotgun?

Remove the cap from the end of the tube and be careful of the spring which is under pressure. The plug will come out with the cap.


How do you install gas piston in Remington 58 shotgun?

With the bolt open and locked, remove the magazine nut and slide the barrel and forend off the shotgun. Replace the nut on the magazine tube (you'll see why in a minute). If you look towards the end of the magazine tube (toward muzzle), you will see a round notch in it. Gently let the bolt move forward until the peg in the slide aligns with the round notch, and lift up carefully. When the slide releases from the piston, the piston will slide forward until it hits the magazine nut. You may now remove the magazine nut and slide the piston and magazine spring from the shotgun. Replace the piston and reassemble in reverse sequence.


Stevens model59a 410 shotgun with a tube feed magazine what is it worth now?

Steven 410 shotgun with a tube feed magazine what is it worth now


Is it harmful to remove the plug in a shotgun?

If you are referring to the magazine tube plug. The answer would be No. It is put there for bird hunting regulations only.


Can a cartridge remain chambered in the M500 shotgun after removal of all cartridges from the magazine tube?

Yes. Shotshells are fed from the magazine tube to the chamber. When the last shotshell is fed from the magazine to the chamber, the magazine is empty, but the shotgun remains loaded.


How do you take the plug out of a Remington 1100?

Remove the magazine cap and forearm, then remove the barrel and mag tube. At the end of the tube will be a metal cap that you can carefully pry out with a screwdriver, some press in and turn to remove them. Use caution, it is under spring pressure.


How do you remove a plug from an Ithaca model 51 autoloader shotgun?

To remove the plug from an Ithaca Model 51 autoloader shotgun, first ensure the firearm is unloaded and pointed in a safe direction. Disassemble the shotgun by removing the barrel and then locate the plug, which is housed in the magazine tube. Use a flathead screwdriver to unscrew the retaining screw if present, then carefully pull the plug out of the magazine tube. Reassemble the shotgun once the plug is removed, ensuring all parts are secure.