0
A revolved section is made by revolving a cross section view 90° about an axis of revolution and superimposing the section view on the orthographic. A removed section is similar except the view is removed to another part of the drawing.
: )
Wiki User
∙ 12y ago
Anonymous
What is difference between removed section and revolved section
Add your answer:
Earn +20 pts
What is the difference between a revolved section and a removed section?
Revolved section shows only the features on the cut plane. It is used to depict the section ofan elongated object without the need to show the entire sectional view. Instead ofprojecting the section onto an adjacent view, the resulting section obtained from the cuttingis revolved 90° and is placed on the same viewwhile Removed section is similar to revolved section in that only the cut plane is shown.However, the section is placed elsewhere on the drawing
In the water analogy of an electric circuit what corresponds to the power supply the resistor and potential difference?
Power supply: Water pump, producing pressure at its output valve.Resistor: A section of pipe. Flow of water loses energy on the way through, due to friction with the pipe's interior wall.Potential difference: Difference in water pressure between the beginning and end of the pipe section.
What is the difference between an you beam and a beam?
An 'U' beam is a beam that is shaped like the letter 'U'. It is usually made of 3 parts; 2 sides and 1 bottom piece. A beam would normally refer to an 'I' beam (A beam that is shaped like the letter 'I'). The difference is that cross section of the beams are different.
What is the difference between resistance and the resistivity?
Resistance is the value of a given wire in ohm but resistivity is value of the material with which that wire is made in ohm meter. R = rho * L / A Here rho is resistivity and R is resistance. L is the length of the wire and A is area of cross section
What is difference center of shear and center of twist?
The shear center is the point on a beam cross section at which an applied shear force (lateral load or load parallel to the cross section) will produce bending but no twisting of the section. The center of twist is a point in a cross section that remains stationary when a twisting moment (torque) is applied on that cross section. The shear center and twist center are the same point only when the beam is rigidly supported.
What is the difference between a revolved section and a removed section?
Revolved section shows only the features on the cut plane. It is used to depict the section ofan elongated object without the need to show the entire sectional view. Instead ofprojecting the section onto an adjacent view, the resulting section obtained from the cuttingis revolved 90° and is placed on the same viewwhile Removed section is similar to revolved section in that only the cut plane is shown.However, the section is placed elsewhere on the drawing
Types of section drawing?
1. Full Section 2. Half Section 3. Local Section 4. Offset Section 5. Revolved Section 6. Removed Section
Difference between cross section and block diagram?
difference between cross section and block daigram
Difference between section and article?
no ans
What is the difference between a half and full section?
A full section is an entire section. A half section is half of a full section.
What is the difference between NCAVC and the BAU?
The BAU is a section of the NCAVC.
Define sectioning in technical drawing and its types?
Sectioning is the process of drawing an object imagining it to be cut throw by a cutting object. TYPES OF SECTION. Full section, Half section, Part section, Broken section, Revolved section, Scrapt section
What is the difference between a cylinder and a cuboid?
A cylinder has a circular cross-section whereas a cuboid has a quadrilateral cross-section.
What are the difference between a section common property and exclusive use?
What_are_the_difference_between_a_section_common_property_and_exclusive_use
What is the difference between a cylinder and a rectangular prism?
A cylinder has a circular cross section, a rectangular prism has a rectangular cross section.
What is the difference between a cylinder and an a square prism?
A cylinder has a circular cross section, a square prism has a square cross section.
What are the responsibilities of the operations section chief?
The difference between a Strike Team and a Task Force is:
