0
Like most other screwed on things on the business end of a firearm the magazine tube on the maverick 88 and or Mossberg 500 as well as probably every other shotgun in the wold, the tube is set with loctite or other thread sealer, which should be easily be burned off by applying a bit of heat, so don't risk destroying your weapon by sticking it in a vise and wrenching it off when you can melt the glue away and simply screw off the magazine tube with some oven mitts on.
What else can I help you with?
How do you relace magazine spring in mossberg 500?
To relace the magazine spring in a Mossberg 500, first ensure the shotgun is unloaded and safe. Remove the forend and barrel by unscrewing the magazine cap. Then, take out the magazine tube's spring and follower. To reassemble, insert the new spring and follower into the magazine tube, ensuring the spring is properly seated, then reattach the barrel and forend.
How do you remove the bolt on a mossberg 185 D shotgun?
You have to press and hold the trigger to the rear and the bolt will slide out the back.
How do you remove the plug on a Winchester ranger shotgun?
To remove the plug from a Winchester Ranger shotgun, first ensure the shotgun is unloaded and pointed in a safe direction. Then, locate the plug inside the magazine tube, usually accessible by unscrewing the end cap or the magazine cap. Once the cap is removed, you can slide the plug out from the magazine tube. Reassemble the shotgun by securely replacing the cap.
How can i remove breach plug from mossberg 50 cal muzzle loader barrel?
If you are talking about the 50 caliber muzzle loader barrel for the Mossberg 12 gauge Shotgun model 500 or the Maverick 88 - you can't remove the breech plug. You have to clean the barrel like a flintlock. I just bought one from Mossberg's web page (arrived yesterday 12/21/08). It didn't come with any instructions. Fortunately, I found the manuals online at the following addresses: Muzzle Loader Barrel http://www.mossbergs.com/manuals/Muzzleloader.pdf 12 Gauge Shotgun Model 500 http://pdf.textfiles.com/manuals/FIREARMS/mossberg_500.pdf Good Luck
How do you remove the magazine tube from Charles daly 20 gauge shotgun?
To remove the magazine tube from a Charles Daly 20 gauge shotgun, first ensure the firearm is unloaded and the action is open. Locate the magazine cap at the end of the magazine tube, unscrew it counterclockwise, and then carefully slide the magazine tube out of the receiver. Depending on the model, you may need to remove additional components, such as the forend or any retaining screws, to fully detach the tube. Always refer to the specific owner's manual for detailed instructions related to your shotgun model.
How do you remove the magazine tube from a Browning Gold 10G shotgun?
Best left to a trained gunsmith
How do you take the plug out of a mossberg 535 twelve gauge Shotgun?
Remove the barrel and then unscrew the magazine tube from the receiver.If the mag tube is too tight to remove easily, use pliers or visegrips ONLY on the very last inch of the tube where the barrel screwed in. It's the only solid part on the tube and it won't bend or crush.
How do you remove the magazine tube on a 870 Remington shotgun?
The actual magazine tube that connects to the receiver is brazed in there, so it removing it isn't an optimum solution.
How do you break down a mossberg 835?
1.) Slide the bolt to midway position. 2.) Remove the magazine cap. 3.) Remove barrel by wiggling back right and left until it is free.
How do you dismantle a BPS shotgun?
remove the magazine cap by unscrewing, then the forearm will slip off. then pull the barrel off.
Is it harmful to remove the plug in a shotgun?
If you are referring to the magazine tube plug. The answer would be No. It is put there for bird hunting regulations only.
How do you install a plug on a Browning A500 Shotgun?
To install a plug on a Browning A500 shotgun, first ensure the firearm is unloaded. Remove the magazine cap and slide the barrel off the receiver. Insert the plug into the magazine tube, ensuring it fits securely, and then reattach the barrel and magazine cap. Finally, check that the plug is properly positioned and that the magazine capacity is limited as required.
