0
What else can I help you with?
How do you connect another Wii remote to Black Ops?
turn wii off first sync the remote to the wii by pressing the ped sync button in the wii remote (next to the batterys) and the second red sync button next to the sd card slot. then power wii up insert game and go to disk channel launch game and press A during the wrist strap warning or the black ops intro. should work
How can you turn off a Wii Remote without turning off the Wii?
hold power button on wii remote and the wii goes in to stanby not off
What do i do if power button for my ps2 stays red?
The button which has a red light on it, you should press it (the button) until it goes green. Then your PlayStation is on.
How to play 2 player on Toy Story 2?
I had the same problem. You have to do a synch with your second remote and the Wii console. The second remote has a synch button that you can see when you open the battery compartment. The synch button on the wii console is behind the SD slot door. Hit them simultaneously while in Toy Story Mania and the second remote will be recognized. After that, hit the small "+" button to play along with player 1.Here's a copy of the detailed syncing directions:Press the Power button to turn on the Wii console.Open the SD Card slot cover on the front of the Wii console.Remove the battery cover from the back of the Wii remote you wish to sync.Press and release the red SYNC button inside of the SD Card compartment on the Wii console.Press and release the red SYNC button below the batteries on the Wii remote.The syncing is complete when the blue LED on the Wii remote stops blinking
How do connect a PS3 remote to a PS3 after it has been connected to a different PS3?
Turn on your PS3 by pressing the "power" button on the console itself. Then connect your controller via the charging cable. Finally, when on the XMB menu, press the PS button on your controller. Happy Gaming!
What do you do when the Wii will not turn on?
If the power light is green, the console is already on.If the power light is red or yellow, try using the power button on the console(as opposed to the power button on the remote).If the power light is black, the power might be out, it might be switched off at the mains, or it might not be plugged in properly.
How do you power on your Wii?
Press the power button on the console, or if you have a Wii Remote connected to the console, the power button on the remote. The power button on the console is located to the top-left of the disk slot, and above the D-Pad on the remote.
How do you program a sears 139.53859 garage door opener?
If you want to add a remote, press the "set" button on the power unit until the green light blinks, then press the button on the remote. If you want the unit to forget all old codes and accept only the new remote, hold the "set" button until the green light stays on solid, then press the remote button.
Need hunter fan remote directions?
To program a Hunter fan remote, start by turning off the fan's power, then press and hold the fan's power button. While holding the power button, turn on the fan's power. Keep holding the power button until you hear a beep or see a light on the remote indicating it's ready to pair with the fan. Finally, press the "Learn" button on the remote to complete the pairing process.
How do you program second remote for dish network?
To program you Dish TV remote to your TV you need to find your remote code to your television.To do this, you will need to do a Dish power scan.First make sure your TV is turned onThen hold down the 'TV' button at the top of your dish remote (it will light up red) until all 4 buttons at the top light upPress the large red power button at the top of your Dish remotePress the channel up (above the select button on most Dish remotes) slowly until the TV powers off to a black or blue screenOnce the TV turns off, press the pound key '#' located at the bottom of your dish TV remote
How can I reprogram my ceiling fan remote?
To reprogram your ceiling fan remote, first, turn off the power to the fan. Then, locate the reset button on the remote and press it. Next, press and hold the reset button on the fan itself. Release the buttons when the fan light blinks. Your remote should now be reprogrammed.
How can I reset a Hunter fan remote?
To reset a Hunter fan remote, you can usually press and hold the fan's power button for about 5-10 seconds until the light on the remote blinks. This should reset the remote and allow you to reprogram it as needed.
How can I reset my Hunter fan remote?
To reset your Hunter fan remote, you can usually press and hold the fan's power button for about 5-10 seconds until the light on the remote blinks. This should reset the remote and allow you to reprogram it as needed.
How to start ATV 110 with remote?
push the lock button then push the power button
How do you programme a new remote to a Panasonic TH 37PV60E?
To program a new remote to a Panasonic TH 37PV60E, first, insert the batteries into the remote. Then, turn on the TV using the power button on the unit. Next, press and hold the "TV" button on the remote until the red LED light turns on, then release the button. Finally, press and hold the "Enter" button until the LED blinks and turns off, indicating the remote is programmed. If it doesn't work, refer to the remote's manual for specific pairing instructions.
How do you reprogram a remote start pursuit key fob on a 2005 Escape?
Easy just hold down your power button until the light on the remote flashes. Then the TV will come on by it's self.(Note: if it does not work somethings wrong with your remote.)
How can I reset my Hunter fan remote control?
To reset your Hunter fan remote control, you can usually press and hold the fan's power button for about 5-10 seconds until the light on the remote blinks. This should reset the remote control and allow you to reprogram it as needed.
