You will need to cut the end off the controller wire, then cut the male end of a usb wire and connect the red,yellow,black and white wires together from both usb and controller. Then heat srink the cut wires so nothing can touch. Then do a Google search for the needed drivers. The drivers are the most important part as without them the controller will not work at all.
plug it into the usb port
make a triangle
Power it. The sensor bar is really just a collection of infrared LEDs. With the standard sensor bar, just plug it into the back of the Wii console.
They make a PS2-like controller for the PC. You just have to install the driver. I don't see why they wouldn't make an XBOX-type controller for the PC.
If you have a controller that will vibrate go to the settings menu and correct the setting
A MIDI controller sends MIDI note messages to another device by MIDI cables or USB to a computer. If it is strictly a MIDI controller with no onboard sounds, it will have to connect to another MIDI device or computer to make sounds.
How the wire or cable allows the PS3 and controller to connect allowing them to establish a bluetooth connection. There is no way you can connect them without a wire to allow the link. You asking can you MAKE A LINK BY HAVING A LINK. No you can not you need the USB to Mini USB cable and after that it will remember the controller. You can borrow one but you should have at least 2. I have 4 because I keep a number of controllers plugged into a hub to allow them to charge
plug it into the usb port
On the front of the controller there will be a small button on the left side (left if you are holding the remote normally) There will then be a button that looks similar to that one on the console. Make sure the xbox and controller are both on, press and hold the button on the controller, then press and hold the button on the console. If it works, then the controller light will flash 3 times and connect.
To register your Sixaxis/DualShock 3 PlayStation 3 controller with your PlayStation 3 system after it has been used with another system, simply connect it to the PS3 with a USB cable and press the PS button on the controller to sync it. Your controller will now work again.
It depends on video card. If you don't have DVI slot then you will have to get a female VGA to male DVI adaptor. the DvI would then go to M1 and connect at projector.
Broken controllers should be replaced. If you connect your charging cable to the PS3 USB and the controller and it still will not work buy a new one. You should have more than one anyway
The PS3 was developed to run a Dual Shock 3 controller and making another controller "work" is really not good enough. Whatever your reasons for wanting the other controller to be able to be used does not mean it will give you the same capabilities even if you are able to make the device work. I do not know the controller you are talking about or whether it is even one of the three named. The Bass Landing Fishing Controller/Rod/Reel for Playstation by Agetec or the Agetec ASCII Grip or Agetec ASCII Pad none were developed for the PS3 or are made for Bluetooth controller connection and can only be made to "work" if they can be connected through the USB port of the PS3 with some sort of adaptor system. They might not work even if you do find a system to connect them and the performance even if they appear to work may not be consistent with every game or even throughout the game
First you go to the top of the controller, right of the left trigger and left of the center of the controller. There is a small round button with a thing that look's like the signal strength of a cell phone above it. Press and hold that till the center button lights start turning clockwise. Then Press the connect button on your xbox. It will then automatically connect the controller to that xbox. Repeat this process if you want to do this on another xbox
make a triangle
If the controller has a sound engine, such as the M-Audio ProKeys Sono, then you can. If it doesn't have an audio output then it doesn't make its own sound. You'll need to connect it to a computer or MIDI sound module to make sounds. That device can then be amplified.
Digital camcorders either work on battery or on AC power adaptor supplied with the camcorder. The DC output connector of the AC adaptor will connect to DC power input socket on the camcorder body. The location of this socket will depend on the make and model of the camcorder. Some times this socket is covered by a rubber cap which needs to be pulled out before you connect the power. - Neeraj Sharma