0
What else can I help you with?
How many watts does the behringer xenyx 802 have?
Xenyx 802 is not a powered mixer, you need a separate amplifier with it to drive the speakers
How do you hookup a stereo mixer to a powered mixer?
stereo mixer output to powered mixer input
How much does a bosch mixer cost?
"Depending on the model, the condition (new or refurbished) and the number of attachments purchased with the mixer, a Bosch Mixer costs from $300.00 to over $600."
Can I run a mixer through my powered mixer for drum mics?
Yes. In fact, I would recommend doing this instead of just running the mics through your band's powered mixer. That way, all your drum sounds (pre-mixed) will fit into just one input on your band's powered mixer. It takes about a minimum of 6 or 7 mics to capture a drum kit properly and that's a hell of a lot of inputs to be using on your band's P.A. Just run the mics through your own mixer, then run your mixer's "Main 1" output to your band's P.A. input. Use a balanced cable. Also, if the mixer that you are using is unpowered, then get yourself a couple powered monitors to run directly off of it so you can have some monitoring without using one of the the P.A. monitors. If your drum mixer IS powered, however, just get yourself some speakers and you've got yourself some monitors. In a nutshell, I recommend getting a small powered mixer for your drum mics (something with 100W minimum) with unpowered monitors running right off of it (use the "Main 2" output). Connect the mixer's "Main 1" output to your band's P.A. system for the final mix. But remember, if you do it like this, you have to dial in a good mix on your drum mics through your own little mixer because the sound guy will only be able to adjust the volume of the drum kit AS A WHOLE through the main P.A. system. This is what I do and it works very well.
What are the ratings and certificates for The Wombles - 1973 The Cement Mixer 1-29?
The Wombles - 1973 The Cement Mixer 1-29 is rated/received certificates of: Australia:G
What cable would you need to connect a behringer mx400 mixer to a behringer vt100fxh head amp?
A HDMI cable is used to connect a behringer mx400 mixer to a behringer head amp. This can be bought at just about an big store.
How Do you wire a USB condenser Microphone to a Behringer Xenyx 302 Mixer?
You cannot connect a USB microphone to a mixer. It must be connected to a computer. The Behringer 502 can accept any dynamic or condenser microphone with an XLR connector .
How do you connect your Behringer 1832FX to your PA system?
Mixer main out (two XLR connectors) to PA amplifier inputs.
How do you hook up Behringer mixer to Amplifier?
You connect the mixers main outputs to the inputs of the amplifier and the outputs of the amplifier to speakers
How TO you find a new power cord for a behringer 1202FX MIXER?
Search for Behringer AC Adaptor.
You Have a Behringer audio mixer and you want to know what effects processor to get?
The Behringer Virtualizer 3D FX2000 if you have a limited budget, the TC Electronic FireworX if you have an unlimited budget.
How much would it cost to buy a Behringer mixer?
The Behringer is a digital mixer that mixes music. The prices range from sixty-four dollars to two thousand nine hundred and ninety nine dollars depending on the make or model chosen.
How many watts does the behringer xenyx 802 have?
Xenyx 802 is not a powered mixer, you need a separate amplifier with it to drive the speakers
What year was the behringer mx3282a mixer made?
The usermanual version 1.1 is dated March 2001, so around that time
How do you connect an audio interface to a mixer?
To connect an audio interface to a mixer, you typically use audio cables to connect the output of the audio interface to an input on the mixer. This allows you to route audio signals from the interface to the mixer for further processing or mixing.
Behringer eurorack ub 1832 fx pro input mixer fx?
List of the inputs and built-in effects read in the manual.
How can I connect a mixer to an audio interface?
To connect a mixer to an audio interface, use balanced cables to connect the mixer's main outputs to the audio interface's line inputs. Adjust the levels on the mixer and interface to ensure proper signal flow and avoid clipping.
