0
Difference between tunnel and transport mode?
- 11 months ago
- Report Abuse
rahul_g1...
Best Answer - Chosen by VotersIPSec can be run in either tunnel mode or transport mode. Each of these modes has its own particular uses and care should be taken to ensure that the correct one is selected for the solution:•Tunnel mode is most commonly used between gateways, or at an end-station to a gateway, the gateway acting as a proxy for the hosts behind it.
•Transport mode is used between end-stations or between an end-station and a gateway, if the gateway is being treated as a host-for example, an encrypted Telnet session from a workstation to a router, in which the router is the actual destination.
As Figure 1 shows, basically transport mode should be used for end-to-end sessions and tunnel mode should be used for everything else. (Refer to the figure for the following discussion.)
Figure 1 Tunnel and transport modes in IPSec.
Figure 1 displays some examples of when to use tunnel versus transport mode:
•Tunnel mode is most commonly used to encrypt traffic between secure IPSec gateways, such as between the Cisco router and PIX Firewall (as shown in example A in Figure 1). The IPSec gateways proxy IPSec for the devices behind them, such as Alice's PC and the HR servers in Figure 1. In example A, Alice connects to the HR servers securely through the IPSec tunnel set up between the gateways.
•Tunnel mode is also used to connect an end-station running IPSec software, such as the Cisco Secure VPN Client, to an IPSec gateway, as shown in example B.
•In example C, tunnel mode is used to set up an IPSec tunnel between the Cisco router and a server running IPSec software. Note that Cisco IOS software and the PIX Firewall sets tunnel mode as the default IPSec mode.
•Transport mode is used between end-stations supporting IPSec, or between an end-station and a gateway, if the gateway is being treated as a host. In example D, transport mode is used to set up an encrypted Telnet session from Alice's PC running Cisco Secure VPN Client software to terminate at the PIX Firewall, enabling Alice to remotely configure the PIX Firewall securely
Add your answer:
Earn +20 pts
What are Example of ipsec encryption modes?
There are two modes for IPSec. Transport mode and Tunnel mode. Transport mode is for securing end-to-end communication between two computers and tunnel mode is for securing gateway-to-gateway communication. Refer the following links for more info. http://www.omnisecu.com/security/ipsec/ipsec-transport-mode.htm http://www.omnisecu.com/security/ipsec/ipsec-tunnel-mode.htm
What is the difference between transport and transportation?
transport is the means by where goods are moved from to a specified place whereas transportation is the act or the mode of transport
Difference between mode and means of transport?
The means of transport is the vehicle used to move from A to B. The mode of transport refers to the medium in or on which the movement takes place:1. inland surface (street, rail, inland water way); 2. sea (ocean, coastal); 3. air; 4. pipeline;
What are the advantages of using ipsec tunnel mode compared to ipsec transport mode?
it protects against traffic analysis the whole datagram end systems do not need to be modified to gain ip security
What is a mode of transport?
To get from my home to my place of work, my means (mode) of transport is by a bus ride. Though in summer, my mode of transport is by bicycle.
Mode of transport Ireland to England 1800?
The only way to transport between Ireland and England in 1800 was by boats and ships.
What is the difference between transportation and travel agency?
Transportation is the way of travelling more or less mode of transport while a travel agency is an organisation which transports people or goods from one place to other.
Which is cheapest mode of transport?
water transport
What is the difference between Store Display Mode and regular home mode on televisions?
nothing they are both the same
When would you configur a GRE tunnel?
To configure a GRE tunnel, create a tunnel interface by issuing the interface tunnel command from the global configuration mode. To configure the tunnel source and destination, issue the tunnel source {ip-address | interface-type} andtunnel destination {host-name | ip-address} commands under the interface configuration mode for the tunnel.
Describe this mode of transport, road transport?
travel on the road
What is difference between minimum mode and maximum mode of 8251?
The 8251 is a USART (Universal Synchronous Asynchronous Receiver Transmitter). It does not have a minimum and maximum mode.
