0
What else can I help you with?
How can you play DVD on Xbox without remote?
you can play a DVD on the old X-Box without buying anything as long as you have the plug-in or wireless controller you have to press like the A button and some other ones and you need the joystick or arrows...
How do you sink an Xbox 360 controller?
well first you need to have your controler set in front of the system. Next you need to hold down the little circle button,then you hold it for least 1 or 2 mins. then it should be synced
How do you reset your Xbox 360?
Resetting an Xbox 360 is very easy to do. First, you will need to take any disc out of the system. Then you will turn off the system and then turn it on with the controller. Hold down the guide button until the Xbox 360 comes back on. When the system turns on hold down the trigger button and the Y button until the system restarts.
Your Wii remote is not working at all?
You should re-sync it by1.taking off the battery cover2.taking off the plastic flap near the disc slot at the front of the wii3.press the red button inside your wii and hold for 15 seconds4.press the button on your wii remotethis should work. If not so, make sure the wii sensor bar is plugged in properly.or i found this on nintendo.com in supportMost Common: Wii Remote not being recognized by the Wii Console (lights on the Wii Remote flash when you press a button, but then go out) - Getting the Wii console to recognize (or "sync" with) a Wii Remote, especially one that did not come in the box with your Wii console, may require doing a few additional steps before it can be synced. Additionally, a Wii Remote that was working, but is no longer being recognized (or has "lost its sync") may need to be re-synced. Please use the troubleshooting steps listed below, which our experience has shown can solve many Wii Remote issues.Try these steps!Turn the Wii console power OFF by pressing the POWER Button on the front of the console. Unplug the power cord from the wall outlet for a few seconds. After a few seconds have elapsed, plug the cord back into the wall outlet.Turn the power of the Wii console ON. When you see the Health and Safety screen, open the small flap on the front of the Wii console to find a red button labeled "SYNC." Press and hold the SYNC Button down for 15 seconds. This will clear all the syncs on the Wii, allowing you to get a clean start to begin the process described below.After holding the SYNC Button on the Wii console down for at least 15 seconds, you can now "re-sync" your Wii Remotes: With the first Wii Remote you wish to sync, remove the battery cover on the back of the Wii Remote to find a small red button just below the batteries.Press and release the small red button just below the batteries on the Wii Remote; the blue lights on the front of the Wii Remote will blink.Quickly press and release the red SYNC button on the inside of the white flap on the front of the Wii console (picture).When the Player LED blinking stops and stays lit, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).This sync procedure (steps "a" through "d" above) must be followed for each additional Wii Remote added to the system.If you are still unable to get the Wii console to recognize your Wii Remote(s) after carefully following the steps above, please call 1-800-255-3700 for further assistance.
How do you climb a ladder in WWE 13 for xbox 360?
If you are interested in climbing a ladder in WWE 12 for Xbox 360, you need to hold down the L1 button while pressing the x button. This will allow you to jump and grab onto the ladder.
How long do you need to hold down the program button for the garage remote to program?
2.7 seconds.
How long do you hold the sync button to conect the Wii balance board to the Wii?
You don't need to hold it very long. Just a couple of seconds.
How long do you hold the B button to get Princess Peach in Super Mario Bros on Wii?
You don't need to press the B button
What is the address button on your dish network remote?
The DISH remotes don't actually have a specific address button. To access that mode, press and hold the mode button until all the lights on the remote turn on. Once you let go the light will be blinking. From there you can enter a code to program the remote, then press the Pound (#) button!
How can I program a LiftMaster remote to operate my garage door?
To program a LiftMaster remote to operate your garage door, you will need to locate the "Learn" button on your garage door opener motor unit. Press and release this button, then within 30 seconds, press and hold the button on the remote you want to program until the garage door opener lights flash. Your remote should now be programmed to operate your garage door.
How can you change old dish network remote to new remote?
To address the remote to the receiver, you do need to be on the System Info screen. You can accomplish this by pressing the Menu button on the old remote 2 times or by pressing the System Info button on the receiver for certain receiver models. Once you are on the System Info screen just follow the instructions below. On a Dish Network Remote Press and hold the sat button down on the new remote until all the buttons light. release the sat button it should be blinking. press the rec button 3 times. your new remote should now work your Dish Network Receiver.
How do you program a lax max universal remote to a element TV flx3210?
To program a LAX Max universal remote to an Element TV FLX3210, first, turn on the TV. Then, press and hold the "TV" button on the remote until the red LED lights up, then release the button. Next, press and hold the "Set" button until the red LED blinks and then stays on. Enter the code for Element TVs (you may need to refer to the remote's manual for the specific code) and then press the "TV" button again. The red LED should turn off, indicating successful programming.
What is the remote code for an sansonic converter box with a rca remote?
To program a RCA remote to work with a Sansonic converter box, you typically need to use the code search feature on the remote. Start by pressing the "TV" or "CBL" button, then hold the "Setup" button until the red light stays on. Next, enter the code 0000, 0001, or 0002, as these are common codes for Sansonic devices, then press the "Enter" button. If the converter box responds, the remote is successfully programmed; if not, you may need to try other codes or consult the RCA remote's user manual for additional codes.
Need hunter fan remote directions?
To program a Hunter fan remote, start by turning off the fan's power, then press and hold the fan's power button. While holding the power button, turn on the fan's power. Keep holding the power button until you hear a beep or see a light on the remote indicating it's ready to pair with the fan. Finally, press the "Learn" button on the remote to complete the pairing process.
How program GE RC24914 e universal remote for Toshiba television?
To program the GE RC24914 universal remote for a Toshiba television, first, turn on your TV. Then, press and hold the "TV" button on the remote until the red indicator stays on, then release the button. Next, press and release the "Power" button repeatedly until the TV turns off. Once the TV is off, press the "Enter" button to store the code. If it doesn’t work, you may need to try different codes listed in the remote's manual for Toshiba TVs.
Need a code for a sharp tv please?
11559867459 hold menu button and unplug tv 78 times if this does not work spend 5.00 dollars and buy a new remote
How do you Program a Pontiac g6 Keyless Remote?
You have to stick the key in the ignition, hold the lock button on the inside of the door, and turn the car ignition on and off, then let go of the lock button on the inside of the door, and press the lock button on the key. If you purchased the key remote online, you should have gotten instructions. If you need a new one, go here: www.keyless-remotes.com
