0
Add your answer:
Earn +20 pts
How do you adjust vacuum advance on a dodge electronic distributor?
pull the hose off the vacuum advance and some of them have a set screw inside the hole.
Where can i find a vacuum hose for 1995 Lincoln town car?
Any auto parts store such as Auto Zone, Advance Auto, etcetera should have the part you are looking for.
Holley 2 barrel carb running rich how to adjust?
1 Locate the curb idle speed screw and the idle mixture screw; both can be found at the base of the two-barrel Holley carburetor. Turn the screws carefully with a screwdriver or allen wrench depending on which type of screw your carb uses in a counter-clockwise direction, until the screws bottom out and you feel resistance.2 Turn both screws clockwise 1 1/4 turns to use as a starting point to adjust the carburetor. Start the motor, letting it warm up for about five minutes.3 Remove the rubber vacuum hose from the vacuum port on the side of the carburetor. Attach a vacuum gauge to the vacuum port.4 Adjust the screws, moving them 1/8 of a turn at a time in a clockwise direction, alternating back and forth. Continue adjusting until both screws have readings of 600 RPMs on the vacuum gauge.5 Remove the vacuum gauge from the vacuum port on the carburetor, by hand. Attach the vacuum hose to the vacuum port.
How do i disable the ERG valve?
If your EGR valve is vacuum operated, simply remove the vacuum hose from the valve.
What is the typical cause of a vacuum leak in a 2004 Chevrolet Impala?
The most typical cause of a vacuum leak is a cracked vacuum hose. The hoses get brittle with age, and cracks are common.
How do you replace the vacuum advance on a 1970 Pontiac V8?
Remove the distributor cap. Remove the hose to the vacuum advance. Remove the two screws holding the vacuum advance on. Install in reverse order.
How do you adjust vacuum advance on a dodge electronic distributor?
pull the hose off the vacuum advance and some of them have a set screw inside the hole.
How can you fix a leaking auto engine distributor vacuum advance?
You must replace it . Remove the 2 screewes that hold it to the distributor base and it will then slide out and the 90 degree rod will drop out of the bass plate hole as you are moving it. Then put the new 1 on and hook the vacuum hose to it.
Where are the vacuum hoses on a 73 vw super beetle?
If you have a manual transmission and a centrifugal advance distributor, you don't have any. If you have vacuum advance on your distributor, there's one vacuum hose running from the side of the carb to the distributor. If you have an automatic transmission, you've got a hose from the intake manifold to the control valve.
Where do the vacuum hoses go on a 1979 Chevrolet C-10 pickup?
There will be a vacuum hose that comes from the brake booster and hooks to the biggest port on the back of the carburetor. There is a vacuum hose that will come from the vacuum advance on the distributor and hook to the left small vacuum port on the front bottom of the carburetor. If you look at the front center of the carburetor at the bottom of it you will see a big vacuum port. The PCV valve hose will hook there and go in the top of a valve cover, should be driverside front. If it is a auto-matic transmission then there will be a long vacuum hose that is hooked to the modulator valve on the passenger side of the transmission and will go to a vacuum tee that you will see on the back of the intake manifold right behind the carburetor. Now I know there are other things on the engine that have to do with emissions but I long as you do not have to have it inspected you can disregaurd the rest of the stuff. The things that I told you about up above is all that you need to hook up to make this engine run good. All the other open vacuum ports can just be pluged off. I hope I've helped you. NEUTZ.
What does the gray heater vacuum hose hook up to?
If it's the one in the engine bay you talking about, there is one that connects to the heater tap on joint to the heater hose.
Where does the hose from the distributor go to on a 1985 Chrysler fifth ave?
This must be a vacuum hose, with a connection to the intake manifold, at rear of carb. This must be an after-market distributor because the original "Lean Burn" computer did not have a vacuum advance distrib. The vacuum was connected to the computer that controlled the distrib. advance. these setups, one made by Mopar, kit #P3690426, by passed the computer and is vacuum operated.
Which carburetor outlet do you use for hose from distributor vacuum advance chev 327?
you need manifold vacuum. Either on one of the intake runners or at the base of the carb.
How do you adjust a crane adjustable vacuum advance?
Go to cranecams.com and download the instructions. NEW ANSWER: Remove the Vacuum hose from the vacuum advance, and put a small screew driver into the hole and turn the screew in or out. Need to turn it, then drive it. Just play with it till you get the best performance out of it.
How do you adjust the vacuum advance on a ford 302 distributor?
>you don't adjust the vaccuum advance. you adjust the distributor. then when engine is running the vaccuum advance will work automatically to the needs of the engine< As a matter of fact, the Ford vacuum advance is easily adjustable. Put a 1/8" Allen wrench through the open of the vacuum advance canister where the vacuum hose goes. Screw it in to slow the rate of advance and screw it out to speed it up. I think it works on a spring preload system.
How do you hook up manuel vacuum hose for an inground pool?
You should have a vacuum plate with a hole in it for the he hose to be plugged into. The vacuum plate is a disc shaped object that fits over the leaf basket in the pools static skimmer box. If you cant find one you may have to get one from a pool shop.
How is vacuum hose diagram?
the hose that fits on the air filter on my 88 dodge dynasty was taken loose from the motor, I know it fits on to the manifold but I can't find where it hook up. help
