0
What are the torque specifications for the water pump bolts on a 1992 Dodge Dakota?
For all 1992 Dodge Dakota V6 andV8 engines:
- All of the water pump bolts are to be torqued to 30 ft. lbs.
For 1992 Dodge Dakota 4 cylinder engines:
- Upper bolts are torqued to 21 ft. lbs.
- Lower bolts are torqued to 40 ft. lbs.
- Waterpump housing-to-cover bolts are torqued to 105 inchlbs.
What else can I help you with?
How do you remove transmission from 1988 dodge Dakota 4x4 3.9liter motor?
How do I get to the flywheel bolts on a 98 dodge dakota to remove a transmission
Can you reuse the head bolts on a corsa 1.6?
I would not recommend it. The bolts are stretched during the torque procedure.
What are the torque specs for a toyota 4ac?
For what? Without knowing, I will give you the head bolt specs. First, always use new bolts. Begin in the middle. Then go to the ends. Never tighten two bolts on the same side in sequence.. First torque them to 22ftlbs, the go around and do them again give them 1/4 turn. 90 degrees. Then do that AGAIN, go around the sequence a third time and give them another 1/4 turn. Toyota provides no specifications for the final ftlbs of torque.
Can't remove 1987 dodge Dakota starter with V-6?
i have a 87 dodge Dakota v-6 pick upat the bottom of the bell housing there are 2 bolts one on each side that hook to a bracket.that hooks to the moter.remove both bottom bolts,you will be able to move and bend the bracket on the starter side out of the way,also will be able to pull the sheet metal gauard from the lower half of the bell housing out.take the top and bottom bolts out of the starter you will need to twist and turn the starter to get it out.but its not all that bad.that is the way i did mine hope this was some help to you Dave
What is torque on the head bolts 2002 Cavalier 2.2?
The 2002 Cavalier 2.2 liter engine cylinder head bolt torque specification is 120 pounds. The cylinder head bolts should be torqued in 40 pound intervals.
What is the torque for oil pan bolts on a 1996 dodge Dakota?
215 in. lbs
Torque specifications bolts suzuki esteem?
torque specifications
What is the Torque setting for transmission pan on 89 dodge Dakota?
12ft lbs for transmission pan bolts
What is the torque specs for power steering pump replacement for 2001 dodge Dakota 3.9L?
For a 2001 Dodge Dakota with a 3.9L engine, the torque specifications for the power steering pump mounting bolts are typically around 18-25 ft-lbs. It's important to consult a repair manual or service guide for the exact specifications and sequence, as they can vary slightly based on the specific model and any updates. Always ensure to use a torque wrench for accurate measurements to avoid damage.
What are the specific torque specifications for the m5 bike bolts?
The specific torque specifications for the m5 bike bolts are typically between 5-7 Nm.
What are the torque specifications for a 1996 Dodge Intrepid main barring cap bolts?
The 1996 Dodge Intrepid main bearing torque specification is 180 pounds. The main bearings should be torqued in 60 pound intervals.
What is the torque for an 1986 Dodge 318 rod bearing bolts?
the correct torque for these bolts is as follows: 96lbs
What are the head bolt torque specifications for a 1987 Dodge D100?
The head bolt torque for the Dodge 6 cylinder and V-8 engines is 50 ft. lbs. torque. If it is a diesel engine, the torque is 90.4 ft. lbs. Tighten the bolts by working from the center out, and alternating side to side. This prevents warping of the head.
Torque specification for 98 Ford F-150?
what is the torque specifications for the intake bolts on a ford 4.2L?
What are the torque specifications for head bolts on a 1997 Chevy silverado?
65ft. LBS
When i torque trans pan bolts on a 2004 dodge Dakota?
13 FT. LBS or 17 N.m That is for the 42re transmission The 46RE is the same also. Good Luck.
How do you remove transmission from 1988 dodge Dakota 4x4 3.9liter motor?
How do I get to the flywheel bolts on a 98 dodge dakota to remove a transmission
