answersLogoWhite

0


Best Answer

The term cock and valve are used interchangeably in the English language. The term cock has in large been replaced with valve with no functional difference between the two.

User Avatar

Wiki User

10y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What is the functional difference between cock and valve?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Engineering

What are the electrical accessories used in artouste engines?

control box , micropump, electric fuel cock, start valve, start cut out switch, starter generator, mini oil pressure switch, oil pressure transmitter and start card.


When would a gate valve be preferred to a ball valve?

Gate Valve is * Well sealed * Causes a low pressure drop * Don`t Cause hammering * serve Wide size Range * Wide range of temperature * Wide range of temperature Ball Valve is * Limited in usage for Temperature cautions * Needs a big Operating Torque for big Sizes


What are the advantage of SMAW process?

Advantage of smaw :*equipment is relatively inexpensive Equipment is portable because the welding machine can be powered with gasoline or diesel powered w/ engines.


How do you open the drain cock on a 2000 jeep Cherokee?

It's behind the passenger side headlight Bezel. Remove the grill, then you can remove the bezel and you will see it. It's almost impossible to turn due to the limited space around it (nice engineering Jeep). If you have a set of 90 degree needle nose piers you should be ok. I didn't and had to really fight with it.


What is the origin of a cockpit in aircraft?

A cockpit is the area, usually near the front of an aircraft, from which a pilot controls the aircraft. Most modern cockpits are enclosed, except on some small aircraft, and cockpits on large airliners are also physically separated from the cabin.Cockpit as a term for the pilot's compartment in an aircraft first appeared in 1914. From about 1935 cockpit also came to be used informally to refer to the driver's seat of a car, especially a high performance one, and this is official terminology in Formula One. The term is most likely related to the sailing term for the coxswain's station in a Royal Navy ship, and later the location of the ship's rudder controls.http://en.wikipedia.org/wiki/Cockpit_(aviation)Also, consider the slang meaning in English of "cock", in context of holding a control stick in an aircraft that is located between ones legs.

Related questions

What is the difference between sublimation deposition?

The Cock Of The Horse Slides Past The Uevuila


What is the difference between a cock and a cockerel?

one ends with just a k and the other ends with a kerel


What is the facial differences between a silkie pullet and silkie cock?

whats the difference between silky cocks and pullets in chicks


What is a ball cock?

The valve that shuts off the water in a toilet cistern is known as the ball-cock. It is operated by a hollow ball attached to an arm, once the ball floats to a certain level, the valve shuts off the water. This action prevents water flowing out of the over-flow pipe to the outside. The ball and valve is known as the ball-cock.


Dump valve hdi?

Why do you want one, just makes you look a cock.


Why it is necessary to turn off the gas with the gas cock rather than with the valve on the burner?

When you leave the gas cock open when you turn off the burner valve, and someone moves the burner to another gas port, there would be a serious gas leak until you turned off the gas at the gas cock.


What is the gas cock?

The gas cock, also called a petcock, is a small valve at the bottom of a motorcycle's gas tank that allows to shut off the flow of fuel to the engine.


Why is it necessary to turn off the gas with the gas cock rather than with the valve on the burner?

Turning off the gas with the gas cock ensures that the entire gas supply is shut off, whereas turning it off at the burner valve may only stop the flow to that specific burner. It is safer to turn off the gas at the source to prevent any potential gas leaks. Additionally, using the gas cock helps protect the valve on the burner from wear and tear.


What is the difference between blowing a cock and sucking a cock?

Both phrases are vulgar terms referring to oral sex acts involving a penis. "Blowing a cock" typically refers to oral stimulation using breath and mouth movements, while "sucking a cock" specifically highlights the action of drawing or pulling with the mouth.


How do you tell the difference between a goldfinch cock and hen?

The male is a bright yellow in spring and summer, with a black cap, wings, and tail. The female is a dull olive green bird, with blackish wings and tail. In winter the male moult makes him resemble his mate, and he will regain his summer colors in the spring moult.


What is gas cock in the Bunsen burner?

A gas cock in a Bunsen burner is a control valve that allows the user to adjust the flow of gas to the burner. By turning the gas cock, the user can increase or decrease the flow of gas, which in turn alters the flame intensity and temperature of the burner.


What is the use of pinch cock valve?

A pinch cock valve is used to control the flow of fluid in a flexible tubing by pinching the tube closed. It is commonly used in laboratory settings or in medical applications where precise flow control is required.