answersLogoWhite

0


Best Answer

the gear ratio is the only difference. In the M20 and M21 the gears were cut with more of a slope or angle to them, while M22 gears where "straight cut" and having almost no slope to them at all. This is why the M22 has it's distinctive whine when under load. The cases are the same but its what's inside that counts !

User Avatar

Wiki User

12y ago
This answer is:
User Avatar
More answers
User Avatar

Frank Abad

Lvl 2
10mo ago

No one has said anything about the length difference between the M-21and the M22. I have had both and the M-22 is about an inch longer.

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What is the difference between a muncie m21 and m22?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How much oil does a muncie 4 speed hold?

There are several versions of the Muncie 4 Speed, Muncie M21 & M22 the SM465's and the SM420's. The SM465's for example were used in 1968-1991 General Motor Trucks Fluid Capacities should be in the 8.4 pints area from what I can find. Hope This Helps.


What transmission to run in a 350 chevy small block?

For an automatic, Powerglide, Th350, Th400. These are the older ones. Powerglide has 2 forward gears, with about a 1.80 first gear. The Turbo Hydros have 3 forward gears, with about a 2.60 first gear. Early stick shift trans are, Saginaw 3, or 4 speeds, which were made in the 70's, and are not strong. Muncie M20, M21, and M22's, were all 4 speeds, made by Chevy in Muncie indiana, and were used behind small, and big block Chevies. M20 is a 2.20 low gear, closer ratio, for road racing. M21 was 2.56 first gear, and wider ratio for drag racing. M22 was the same as M22, but stronger with straight cut gears, and very noisey. Then, of course, the Borg-Warner super T-10. There were three designs of this trans. All had around a 2.86 first gear. The first design had a cast iron case, and coarse exit spline. Weak. The 2nd, and 3rd designs, were aluminum, and had a fine in, and output spline. Much stronger, and more quiet than the M22. These were "outsourced" thropughout the 60's, and 70's, alternating with the Muncies. These were al the transmissions that Chevy made through the life of the 350. In 88, when the 5.7 debuts, there were another whole line. Most had a four speed with overdrive, however, none had achieverd the strength of the 70's models.


Is a m22 a rifle?

There is a rifle called the M22, yes.


Do you have a m22 transmission in your 1966 gto?

It looks like the M22 did not come out 'till '67. Not to say it could not have been changed at some point. Find the serial #. '63 to '66 do not have a year designator in the seial #. Example P0101 would mean P- Muncie 4 speed 01 - January 01 - the 1st day From '67 to '68 the month got a letter code and the year code is present. Example - P8A01 : P - Muncie 4 speed 8 - 1968 A - January 01 - 1st day '68 through '74 have a letter at the end to code the ratio.


What has replaced the M8A1 kit?

M22


How do you tell if you have an M20 or M22 transmission in a 1970 Corvette?

An M22 'rockcrusher' transmission is far noisier than an M20 due to the straight cut gears.


How accurate are ruger m22 rifles?

Better than 90% of the people who shoot them.


What size is the hose fitting on a husky pressure washer 3000 psi 2.5gpm?

M22


Which piece of equipment is used for detection for protection and warning?

M22 Automatic Chemical Agent Alarm


Which pieces of equipment is used for detection for protection and warning?

M22 Automatic Chemical Agent Alarm


How many miles belfast to letterkenny?

93 miles taking this route:Take M2 to The NORTH, form Belfast, to M22 LONDONDERRY; continue straight on M22.Take M22 to A6 LONDONDERRY.Take A6 to the road that leads to the FOYLE BRIDGE (at ALTNAGEVIN ROUNDABOUT) in Londonderry.Take the Londonderry by-pass around to A2 LETTERKENNY, via the Foyle Bridge. Then take A2 into IRELAND, where the highway continues as N13.Continue on N13 to Letterkenny, via N14.


A large aquarium has a volume of 125 meters cubed. has glass on the bottom and 4 sides but no top. the edges are reinforced with angle iron. what is the area of glass required?

The aquarium, can be constructed of any quantity of glass 125 square meters or more.In general, the area of the glass required is(2 x length x height) + (2 x width x height) + (length x width).The minimum is the case where the aquarium is cubical, Length = width = height = 5 meters . . .(a large aquarium indeed! It would take 138 tons of water to fill it. But I digress.)(2 x L x H) + (2 x W x H) + (L x W) = 50 + 50 + 25 = 125 square meters.There are an infinite number of other sets of dimensions that also hold 125 cubic metersof volume, but need more glass to build. A few examples are:L - W - H . . . glass1 x 1 x 125 . . . . . 501 m2 1 x 1.25 x 100 .. . 451.25 m21 x 2.5 x 50 .. . . . 352.5 m21 x 5 x 25 . . . . . . 305 m21 x 10 x 12.5 . . . . 285 m22 x 1.25 x 50 . . . . 327.5 m22 x 2.5 x 25 . . . . . 230 m22 x 5 x 12.5 . . . . . 185 m22.5 x 2.5 x 20 . . . . 206.25 m24 x 2.5 x 12.5 . . . . 172.5 m24 x 5 x 6.25 .. . . . . 132.5 m2