0
In my laptop wireless connection showing sent activity but activity received showing zero and in support its not showing default gateway how to add this default gateway?
Abdulsattar
i am experiencing the same problem in my new PC. My ISP isa saying my vendor has some sort of firewall installed that is preventing me to ping my defualt gateway.
I am also looking for the solution.
anyone?
The most likely answer is that your wireless card is not properly configured to connect with your network. The sent activity is coming from your wireless card attempting to contact the router and then the network; the lack of incoming packets means that the router is not receiving your sent signals.
I would suggest setting you laptop next to your wireless router and attempting to configure your network from there. This would eliminate almost all chance of being out of your router's range.
The configuration menus change by make and model of your router so I can't provide any specifics only a general list of steps to take.
First I would open up Command Prompt (Start>Programs>Accessories) and then type "ipconfig" and press enter. This will provide you with the general information and configuration of ALL enabled network devices that are part of your computer. This means that if you have a wireless card and an ethernet card (wired) the status will show up for both.
typing "ipconfig" will tell you your internet Protocal (IP) address. This will most likely be something like 192.168.0.X where X is a number between 1 and 255. If your IP is not within this range then your router has been altered from its factory settings and your problem would need hands-on help.
ipconfig would also tell you your subnet which should be 255.255.255.0 and your default gateway wich may or may not be displayed.
Sorry for the long answer but it isn't exactly an easy problem to solve. It would really help to have you trying the steps I have suggested while in communication so I may provide more specific answers.
Hope this helps
Zilduli
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How secure is a wireless network router, will my neighbors be able to use my connection?
Wireless networking can be very tightly secured, but with default settings the connection is easily stolen by neighbors with the appropriate knowledge.
How do you bypass pressing the F2 key each time you want to get on the internet?
This is a standard wireless router connection protocol. You would have to reset the router's default settings.
How to Convert HP deskjet printer 940C to wireless?
Connect the printer to a network computer that is connected via a wireless router. If that doesn't work, use the built in WiFi connection and tell the computer to look for it and add it is a separate printer, then set it as the default printer.
Your laptop does not detect wireless network your PC is connected to the router and internet works fine. The laptop detects networks elsewhere?
The wireless is not enabled on the router or the SSID is not being broadcasted. Both of these setting are in the router configuration. I would recommend calling the router manufacturer and have them help you enable the wireless, it's different for each model. Your desktop PC works because it's probably using a wired connection, which is enabled by default. Wireless is not usually enabled by default.
How can you use your WiFi AP solo?
i. Setting up the access point as an access point - The Access Point mode is the default setting of most Linksys wireless access points. It allows you to extend the range of an existing wireless signal by connecting the access point to a wireless router via Ethernet connection.
How do you get Nintendo wifi connection working on a dsi XL on a netgear WNDR 3400?
Go to your wireless router settings and change the "channel" to 01. This setting is in the Basic Settings/Wireless Setup. The default is set to "Auto". I then manually set up in Internet/Connection Settings on the DSi XL. Choose Advanced Setup and then choose Connection 4, Change Settings, enter the SSID, choose the correct security setting and then enter the key. This worked for me!
Which method establishes an administrative connection for configuring the Linksys WRT300N wireless access point?
From a computer in the same IP subnet as the access point, enter the default IP address of the access point in a web browser.
Default user name and password for wired connection?
No
What is the default tcp port number for a POP3 connection?
110
Can a WiFi connection be accessed without configuring a wireless modem?
Yes, it can. Usually default settings include configured DHCP server, no security, no mac filtering, broadcast SSID is on. In another words, it's configured in a way it's very easy to establish connection with it.
If I print wireless at work on laptop can I print with USB at home?
Yes you certainly can. The wireless connection at work and your USB connection at home are two separate and independent connections and they will be pointing to two separate printers, as a matter of fact you can set up a number of printers on your Laptop each will have it's own separate connection if you have multiple printers set up you will need to specify the particular printer you want to print to when prompted otherwise your print job will be sent to the printer you have designated as the default printer.
Wireless not working and is switched on but windows diagnostics says it is not on?
Try using utility from the wireless adapter manufacture. Also there are always two options to manage wireless cards. By default windows wireless zero does not have access to the wireless adapter. Try changing the last option in wireless adapter properties.
