0
How do you know which light bulb is bad on a Christmas string of lights?
Wiki User
∙ 12y ago
Plug the "string of lights" into the power point. If a particular light does not come on, then it is "bad".
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What happens a lot if one bulb breaks in you Christmas lights?
it depends on what kind of Christmas lights you have
What is a G40 light bulb?
G40 lights are often used on Christmas trees. These lights are slightly bigger and brighter than traditional tree lights and are also safe to use outdoors.
What does a light source do?
It's simple the light bulb brings light when it is dark.it lights up the house how does it light up. it has a cord which electricity passes through and lights up the wire
What is a seris and a parrel circut?
in a series circuit current flows through each resistor or light bulb and if one item burns out the complete circuit goes dead such were the old fashioned xmas tree lights. They were wire in series and if one light burned out you had to test each light bulb til you found the one burned out to get the whole string to work again. In a parallel circuit each resistor, motor, light bulb has its own ground so if you lost one light in a circuit the rest of them continue to burn.
Why was the light bulb necessary?
Earlier forms of lighting, such as gas lights, were expensive, dangerous and gave less light than the electric light. Gas lights could not be used in places with a fire or explosion hazard.
Where is the load on a string of Christmas lights?
The load on a string of Christmas lights is typically located in the bulb itself. Each bulb is designed to produce light and consumes power when electricity passes through it. The collective load of all the bulbs on the string determines the amount of power required to illuminate the lights.
What is the difference between series and parallel Christmas lights?
With series Christmas lights, if one burns out, the whole string stops working. With parallel Christmas lights one light burning out only affects that light. This makes it much easier to replace burned out lights in the case of the parallel lights.
Why was the parelllel circuit created?
Remember the old Christmas lights that were a simple circuit. When you plugged the string in, hopefully, they would light up. If they didn't light up, you had to take a proven good bulb and screw it in to each light socket on the string until you found the faulty bulb. With a string of lights wired into a parallel circuit, you or wouldn't have to do that. You could identify the faulty bulb right away because it would be the only one which did not light up.
Where can one find C9 lights in Texas?
One can find C9 lights in Texas from the following online stores; Christmas light etc, Christmas light source, Christmas light and more and Light bulb depot.
What can you use a parallel circuit for?
Christmas tree lights, this parallel circuit prevents one bulb failure from turning off the whole string of lights.
What would be the explanation for one light not working in a strand of Christmas lights?
Bulb blown, perhaps?
What is the red spare Christmas light for?
The spare bulb with the red tip make the lights flash on and off
What can light up a light bulb?
Well. A light bulb lights up because the atoms and electrons clash together which causes an electrical charge. And then it magically lights up the light bulb. By:?
How are Christmas Light Shows made?
In terms of light shows that feature flashing lights, regular Christmas lights are installed in the desired pattern. Then, separate blinking light bulbs are added. You can tell they are different because the tip of the glass bulb is painted red or silver to indicate it is the bulb that will turn on the string's ability to blink. It takes a bit of trial and error once the lights are all sufficiently warm, but many of these light shows are coordinated with computers to run on a timer. That is how the bigger shows (i.e. Walt Disney World) look the way they do.
How much electricity does Christmas lights use per hour?
The average strand of Christmas lights pulls about 1 amp, which is roughly the same as a 100 watt light bulb running on 120 volts. It's hard to say how much running it will cost you for electricity, but one thing is sure: no one wants to leave their light on all day, same goes with the Christmas lights.
How can one make animated Christmas lights?
Animated Christmas lights can be made several different ways; the most popular is to use a flasher bulb at the end of the string so that the lights blink in a certain sequence. These can be purchased in sets as well as coming with specially marked sets of lights.
If one light goes out on a series-parallel connected string do they all go out?
If one light goes out on a series-parallel connected string, all of the lights in that particular series string will go out. The other parallel strings will not be affected. If you are asking about Christmas tree lights, please note that most modern low voltage bulb designs make the bulb short out, rather than open, when the filament burns out. This keeps the other bulbs in that series string on, although they now have more power and are more likely to also burn out.
