0
What else can I help you with?
How do you draw rectangle in logo with repeat command?
In Logo, you can draw a rectangle using the REPEAT command to create the four sides efficiently. For example, you can use the following code: REPEAT 2 [ FORWARD 100 ; length of the rectangle RIGHT 90 FORWARD 50 ; width of the rectangle RIGHT 90 ] This code moves the turtle forward to draw the length, turns right, and then draws the width, repeating the process to complete the rectangle.
What is SETH command used for in logo?
SETCH command is used to point the command its head in any direction without using the RT or LT.
How do you make a flag in msw logo using repeat command?
To create a flag in MSW Logo using the repeat command, you can use the following steps: First, define the size and colors of the flag sections. Then, use the REPEAT command to draw rectangles that represent each section of the flag. For example, you can use REPEAT 3 [FORWARD 100 RIGHT 90 FORWARD 50 RIGHT 90] to create three horizontal stripes. Adjust the dimensions and colors as needed to achieve your desired flag design.
How do you make circle in msw logo using repeat command?
repeat 360[fd1 lt 1]
How do you mke a square using repeat command FOR LOGO?
Repeat 4 [fd 60 rt 90]
How do you draw nonagon using logo command?
repeat 3 [fd 250 rt 120]
How do you draw hexagon using repeat command of logo?
To draw a hexagon using the repeat command in Logo, you can use the following code: repeat 6 [forward 100 right 60] This command will move the turtle forward by 100 units and then turn it right by 60 degrees, repeating this process six times to create a hexagon. Adjust the forward distance to change the size of the hexagon.
What is the logo command for rhombus?
In Logo programming, the command to draw a rhombus can be achieved using the combination of FORWARD and RIGHT (or LEFT) commands to create the desired angles. A typical command sequence might look like this: REPEAT 2 [FORWARD 100 RIGHT 60 FORWARD 100 RIGHT 120], where you adjust the angles and lengths as needed to create a rhombus shape.
What is SETH command used for in logo?
SETCH command is used to point the command its head in any direction without using the RT or LT.
How do you draw an octagon using Logo command?
An octagon is an eight-sided pentagon where all sides are equal length and all angles are equal. To draw an octagon in Logo, you move forward the length of a side and then turn 45 degrees, repeating 8 times (8x45=360). The following will therefore draw an octagon with a side length of 100 pixels: repeat 8 [fd 100 rt 45]
How do you make a trapezium in MSW logo?
Well, honey, to make a trapezium in MSW Logo, you gotta use the "FD" (forward) and "RT" (right turn) commands to draw the sides of the trapezium at different lengths and angles. Just remember to keep track of your angles and side lengths to get that trapezium looking sharp. And if you mess up, just hit that "CLEARSCREEN" command and start over - ain't nobody got time for crooked trapeziums!
How do you make circle in msw logo using repeat command?
repeat 360[fd1 lt 1]
How do you mke a square using repeat command FOR LOGO?
Repeat 4 [fd 60 rt 90]
Write logo commands to draw the rectangle figure?
write the logo commands to draw the triangle
How do you draw a cycle in MSW Logo?
To draw a cycle in MSW Logo, you can use the REPEAT command along with the FORWARD and RIGHT commands. For example, you can type REPEAT 36 [FORWARD 10 RIGHT 10] to create a circular shape. This command effectively moves the turtle forward while turning it slightly, creating a smooth cycle. Adjust the numbers to change the size and smoothness of the cycle.
How do you make a car on msw logo?
To draw a car in MSW Logo you need to type in commands to control the turtle and draw the image. Common command to control directions of the turtle, and thus draw the car, are fd Ã? forward, lt Ã? left, and rt Ã? right. By including a number with these commands you are telling the turtle the length of the line you would like it to draw.
What logo is a white and black cube?
anic
