answersLogoWhite

0

None of the receiver screws need to be removed to tighten or remove the barrel. There is a barrel lock in the barrel lock ring behind the barrel adjusting ring (the hand nut) that should go into receiver and keep the barrel aligned and then just tightening and loosing should tighten up the barrel. If the lock is missing try e-gunparts if not you just need to get all that really cleaned up and well oiled. The 24, 241, and the current browning is still basically the same gun if you want to look at one at a shop for comparison. If you need more help you should head over to the Remington Society of America forums.

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

Replacing barrel on Remington model 12?

Remington Model 12 barrels are threaded to the action. Barrels can be replaced with the proper equipment.


Where can you find a threaded bull barrel for a Remington 597?

You will probably have to contact a barrel maker.


How do you adjust the Remington model 24 barrel?

Adjust? You mean to remove or tighten? There is a threaded tightening bolt right in front of the receiver over the barrel.


Is the Remington wingmaster 870 chokable?

Yes, if it is a modern Remington barrel because these barrels come pre-threaded and accept REM chokes (and many other manufacturer's chokes made for the Remington barrel). Otherwise it will have the choke description stamped on the barrel like, "FULL". I have an older Remington barrel that was a "FULL" choke that I had a gunsmith thread for me. The ability to thread a barrel for chokes will depend on the thickness of the barrel wall. Consult a trained gunsmith.


Is the District V2 deck threaded?

No deck is threaded it is the headset and the forks that can be threaded or threadless


Hex Nuts,?

Kanika Exports are manufactures & exporters of various types of products like- Threaded Rods/ Bars, Coil Rods/ Tie Rods , Threaded Studs, Hex Nuts, Hex Bolts, Plain Washers, Spring Washers, Spring Channel Nut,Strut Channel ,Channel Accessories ,Channel Brackets, Channel Fitting Accessories, Mild Steel Threaded Rods , Zinc Plated Threaded Rods, Steel Threaded Rods, Medium Carbon Steel Threaded Rods, Double Ended Threaded Rods, Fully Threaded Studs, Rolled threaded bars,MS thread rods and bars, UNF Threaded Rods, UNEF Threaded Rods, UNC Threaded Rods, Unified Threaded Rod


Can i connect threaded stainless nipple to threaded brass valve?

Yes.


Are the pedals on this bicycle reverse threaded?

No, the pedals on this bicycle are not reverse threaded.


How do you calculate the number of turns in a threaded screw?

Divide the threaded length by the lead length. For single threaded screws the lead is the same as the pitch.


Can black steel pipe be threaded?

Black steel depending on schedule can be threaded from 1/8" - 8" Personally I threaded up to 6"


Why will your machine not make one stitch?

The first thing you should do if the motor is turning, is check to see if your machine is threaded correctly. Then check to be sure your bobbin is in and threaded correctly. If it still won't sew, check both your upper and lower tension. Adjust until the stitches are even and tight, but not too tight. See related link below for more information on adjusting tension.


How do you compress rear piston on a 88 Saab 900?

Beginning with MY 1988, the 900s had the same brakes as the 9000s. The rear brake piston must be turned in with a special wrench, not compressed as in earlier 900s.According to the manual (you do have a manual, don't you!) you need to remove the threaded screw plug covering the adjusting screw. The piston adjusting screw requires a 4mm Allen head wrench.