0
What else can I help you with?
Does the TR wire connect to the positive connection on a robertshaw7956-336P gas valve?
No, the TR wire on a Robertshaw 7956-336P gas valve does not connect to the positive connection. The TR wire typically connects to the thermostat to control the valve's operation. The positive connection is for the main power supply to the valve.
What does the ATX or BTX power supply the remote switch wire from the case must be connected to before power will come on?
In both ATX and BTX power supplies, the remote switch wire from the case must be connected to the motherboard's power switch header or pins. This connection allows the power supply to be turned on/off using the computer's power button.
What are the steps on how to assemble of a system unit?
To assemble a system unit, start by installing the power supply, motherboard, CPU, and RAM into the case. Next, add the storage devices such as HDD/SSD and connect them to the motherboard. Then, install the graphics card, if applicable, into the appropriate slot. Finally, connect all the necessary cables such as power, data, and front panel connectors, and ensure everything is securely in place before powering on the system.
Where does each cable lead off an 350 watt power supply?
A 350 watt power supply typically has multiple cables that connect to different components in a computer system. These cables typically include connectors for the motherboard, CPU, SATA drives, PCIe devices (such as graphics cards), and peripherals such as fans and lighting. Each cable leads to the corresponding component that requires power for proper operation.
Where do you plug in the power cord in at?
The power cord should be plugged into the power outlet on the back or side of your device. Make sure to connect it securely to ensure proper power supply.
Does the motherboard connect the power supply to the peripherals?
The motherboard does not connect the power supply to the peripherals. The power is supplied directly to most peripherals such as HDDs and CD drives by cables from the power supply. Some special expansion cards, such as network cards, get enough power from the motherboard through the PCI slot to function.
What component connect to the motherboard use of the 24 pin connector?
power supply
How to check the power supply section of motherboard not the smps?
You should not bother to check any power supply in the motherboard. You need to take the motherboard to service centre if faulty.
What does the CPU fan connect to?
The fans usually connect to the motherboard, but they can connect directly to the power supply unit.
Why the case and power supply must match the motherboard?
Case: Your motherboard must be able to fit in your case and must support your motherboard size (correctly placed standoffs). Power Supply: You can't have a shortage of power or else your power supply will get overloaded and "die", or even possibly explode for that matter.
How do I connect a dishwasher to a hot or cold water supply?
To connect a dishwasher to a hot or cold water supply, you will need to locate the water supply line under your sink. You can then use a flexible hose to connect the dishwasher to the water supply line, ensuring a secure connection. Make sure to follow the manufacturer's instructions for the specific type of water connection required for your dishwasher.
Will Ati Radeon HD 5770 work on Optiplex 745?
Yep, that should be working fine. Just connect the 5770 to a PCI slot on the motherboard, and connect the power PCI power cable from the graphics card to the PSU (Power Supply Unit).
How do I properly connect the dishwasher water connection?
To properly connect the dishwasher water connection, first ensure the water supply is turned off. Then, connect the water supply line to the dishwasher's water inlet valve using a compression fitting or hose clamp. Tighten the connection securely to prevent leaks. Finally, turn on the water supply and check for any leaks before running the dishwasher.
What is a 20 pin ATX power connector?
The atx 12 connector is one of the motherboard power connectors and used for 12 volt power connect for cpu voltage regulator.
What were the steps to building a computer?
If you want to build a computer, then you need to make sure that all of the parts are compatible with each other. A computer must have a Power Supply, Motherboard, Processor, Hard Disk, and RAM to function properly. All of these parts screw into the computer case. The first step in building a computer is to make sure that you are properly grounded. Next, install all of the components on the motherboard, before the motherboard goes in the case. Install the compatible RAM into the proper slots on the motherboard. Next, install the processor. Then, attach the fan on top of the processor, to keep the fan from reaching high temperatures. Next, screw the standoffs into the case, to where the motherboard will go. Standoffs prevent the motherboard from touching the case. Then, lay the motherboard onto the case, on top of the standoffs, and screw the motherboard into place. Now, take the 20 or 24-pin AT or ATX cable from the power supply, and connect it to the proper port on the motherboard. Now, you need to connect the Power, Reset, and/or Front USB and Audio connections to the motherboard. Refer to the Owner's Manual for the Motherboard for this. Next, install the Hard Disk. Hard Disks can use either PATA or SATA. SATA operates at faster speeds. You can use either one, depending on the connections on the Hard Drive, and the motherboard. Screw the Hard Drive into the appropriate spot, inside the case. Then, connect the Hard Disk to the motherboard with either a PATA or SATA cable. Then, depending on the connections on the Hard Drive and Power Supply, connect a Molex or a SATA power connector to the Hard Drive. If your Hard Drive has both, only use one of the 2. Do not connect both SATA and Molex power connectors to the same drive. Next, install the CD/DVD drive, if you choose to use one. First, remove the cover for the drive by pushing on the cover, from the inside of the case. Next, slide the drive into the drive bay, from the outside of the case. Then, screw the drive in, using the appropriate screws. Then, connect the CD/DVD drive to the power supply, using either a Molex connector, or a SATA connector, depending on the type of CD/DVD drive, and Power Supply. Then, connect the CD/DVD drive to the Motherboard with either a PATA cable, or a SATA cable, depending on the type of CD/DVD drive, and Motherboard. Next, install the expansion cards into the appropriate slots on the motherboard, if you want to have any. To install an expansion card, first, make sure that there is an interface on the motherboard for the card that you have. Most cards have a PCI interface. First, unscrew the screw that keeps the cover for the expansion card on. Next, carefully insert the card into the appropriate slot on the motherboard. Next, screw the card in, using the appropriate screw. You have now built a computer. Next, connect all of the external peripherals to the external ports. Connect the mouse to either a Serial, Green PS/2, or USB connection. Then, connect the keyboard to either a Violet PS/2 or USB connection. Next, connect the monitor with either a VGA or DVI connection. Next, connect the RJ45 Ethernet cable to the RJ45 port, if you choose to do so. Or, if you are using dialup, connect the RJ11 Phone Line to the appropriate connection. Next, connect the Power connection to the Power Supply. If the Power Supply has a switch, make sure that it is switched to the on position. Next, turn the computer on, and install the Operating System. Make sure that the Operating System is compatible with the hardware in your computer.
Why won't Geforce 9800GT work in my computer?
Were you able to install the card into the slot on the motherboard? And did you connect the little power cable from the power supply to the card? If you did both of these things, then it should work. Download and install the latest drivers for the card from Nvidia's website and that should do it.
Is it better to plug a case fan into the motherboard or the power supply and what happens if you connect it to both?
if the motherboard is designed for the case fan you are using its best to plug it into the motherboard, this will free up a spot on the power supply. Otherwise as long as the voltage and amps are the same it doesn't really matter. If you try to plug it into both you will double the power of the fan and very likely fry the fan.
