0
What else can I help you with?
What is the fuse rating for a kettle?
A standard 3kW immersion heater will require a fuse rating of 13 A. This is because, it draws a current of 12 A.
What protective device should in the consumer unit be rated for a 3KW immersion heater use?
For a 3kW immersion heater, a protective device such as a circuit breaker or fuse should be rated at least 13 amps to safely handle the load. This is calculated by dividing the power (3000 watts) by the voltage (usually 230V in residential settings). It is important to ensure the protective device is properly sized to prevent overheating and potential hazards.
What is the cable size for a 3KW motor 350 meter run for cable 240v?
For a 3KW motor with a 350-meter run and 240V supply voltage, you would typically need a cable size of around 16mm² for proper voltage drop considerations and to prevent overheating. It's recommended to consult with a qualified electrician or use a voltage drop calculator to determine the exact cable size needed for your specific installation.
How many amps does 3kW geyser draw?
Assuming no other factors are considered, a 3kW geyser would draw approximately 13 amps of current on a standard 230V electrical supply. This calculation is based on the formula: Power (in watts) = Voltage (in volts) x Current (in amps).
How long to heat 500 liter water with 3kw element?
Specific Heat of Water = 4.1813 kJ/l/K If starting temperature is say 10°C - 500 Litres * 4.1813 (100°C - 10°C) = 188158.5 kJ 188158.5kJ / 3kW = 62719.5 Seconds = 17.42 Hours
What is the fuse rating for a kettle?
A standard 3kW immersion heater will require a fuse rating of 13 A. This is because, it draws a current of 12 A.
What is the fuse rating for 3kw immersion heater?
The fuse rating for a 3kW immersion heater is typically 13 amps. This is based on the formula that calculates the current draw (I) using the power (P) and voltage (V): I = P/V. For a standard UK voltage of 230V, a 3kW heater would draw approximately 13 amps. It's important to ensure that the circuit is also properly rated to handle the load.
What cable size needed for 3KW geyser?
You need to know the amperage requirement of the pump and then you can calculate the wire size.
What size of wire use for 3kw motor 380volts 3phase?
How to calculate a cable size of 3kw motor
Can the bestway 12ft x 4ft pool connect to a heater?
Yes it can, you can either us a bestway or intex 3kw heater.
What size of wire you need to feed commercial kitchen equipment three 3kwovens a 20kw water heater and 3kw deep fryer?
You should contact a certified, and licensed electrician.
What protective device should in the consumer unit be rated for a 3KW immersion heater use?
For a 3kW immersion heater, a protective device such as a circuit breaker or fuse should be rated at least 13 amps to safely handle the load. This is calculated by dividing the power (3000 watts) by the voltage (usually 230V in residential settings). It is important to ensure the protective device is properly sized to prevent overheating and potential hazards.
How long will a 3kw heater take to heat a 16ft pool?
3kw heater heating a 10 foot pool may take 4 to 8 hours for heating it up to 20 to 25 Degrees Celsius. This also depends on the outside temperature.
What is the cable size for a 3KW motor 350 meter run for cable 240v?
For a 3KW motor with a 350-meter run and 240V supply voltage, you would typically need a cable size of around 16mm² for proper voltage drop considerations and to prevent overheating. It's recommended to consult with a qualified electrician or use a voltage drop calculator to determine the exact cable size needed for your specific installation.
How many degrees will your heat pump raise the temp of your pool?
i have a 5ft pool and have a intex 3kw heater how long will it take to heat pool to a good swimm tempature
What size of cable will you need for a 3 phase panel running 3 3kw motors?
To answer this question a voltage must be stated.
Where should the supply for a 3kW immersion heater originate from?
junction box
