0
I = On
0 = Off
The on position on an IO switch would be the 'I'. That only leaves the 'O' to be the off button. So, the 'I' on an IO switch would be on, and 'O' would be off. The termonology of using I, comes from basic electroincs, where I = current flow (I=E/R). I/O was chosen as an international electrical designation, as it historically crosses all languages where electrical design is concerned.
What else can I help you with?
What happens when we switch plug sockets on?
With the switch in the on position the receptacle is energized. With the switch in the off position the receptacle is de-energized.
What position does the switch have to be in for a circuit to work?
The switch needs to be in the "on" position for the circuit to work, allowing the flow of electricity through the circuit. In the "off" position, the switch breaks the circuit, stopping the flow of electricity.
Which is the safest position for the switch to turn an appliance on and off?
the safest position for a switch is on the live wire and not on the neutral wire
How many switch positions are there in the EPIRB?
There are typically two switch positions in an EPIRB: "ON" for activation and "OFF" for deactivation. Some models may also have a "TEST" switch position for performing self-tests on the device.
What does an open switch look like?
An open switch position typically means the switch is in the off or disconnected state, where the circuit is broken. In a physical switch, the lever or toggle would be in the "off" position, indicating the open circuit.
Can a monster attack right after you switch?
If you switch it from attack position to defence position you can't because no monster can attack from defence position except from "Total defence shogun". But if you switch it from defence position to attack position then you can attack
What happens when we switch plug sockets on?
With the switch in the on position the receptacle is energized. With the switch in the off position the receptacle is de-energized.
What position does the switch have to be in for a circuit to work?
The switch needs to be in the "on" position for the circuit to work, allowing the flow of electricity through the circuit. In the "off" position, the switch breaks the circuit, stopping the flow of electricity.
Buick pnp switch?
Park and Neutral Position Switch
Which is the safest position for the switch to turn an appliance on and off?
the safest position for a switch is on the live wire and not on the neutral wire
Do you have to turn on the switch to reset the tire pressure light?
Yes, the ignition switch must be in the ignition position -not- the accessory position.
How do you fix a p0705 code on a Kia Spectra?
P0705 is the code for the transaxle range signal malfunction. It can be caused by faulty park/neutral position switch, misadjusted park/neutral position switch, the park/neutral position switch harness shorted or the park/neutral position switch circuit having a poor electrical connection. Try changing out the switch.
How many switch positions are there in the EPIRB?
There are typically two switch positions in an EPIRB: "ON" for activation and "OFF" for deactivation. Some models may also have a "TEST" switch position for performing self-tests on the device.
What does an open switch look like?
An open switch position typically means the switch is in the off or disconnected state, where the circuit is broken. In a physical switch, the lever or toggle would be in the "off" position, indicating the open circuit.
Why interior light stays on?
The switch is in the on position.
How can I use the power to switch on the light?
To use the power to switch on the light, locate the light switch and flip it to the "on" position.
How do you choke a chainsaw?
Depends on the saw... On a Stihl chainsaw there is a four position switch. Top position is OFF, second position is RUN/IDLE, third position is HALF CHOKE and the last position is FULL CHOKE. Hold the throttle in with your finger and move the switch down with your thumb. DO NOT try to move the switch down into choke WITHOUT holding in the throttle. On a Husqvarna chainsaw there is normally a switch that you pull out towards you. However, there have been models made that you have to push a switch downwards.
