Wiki User
∙ 14y agoGreen wire must be grounded for safety. The two white wires are phase and neutral.
You can discover which one is the hot wire by using a mulltimeter. But there is no needing to discover it. About the green wire only an electrician can install it properly.
It can be joined to the neutral wire, but it is not advisable for any electrical device. The correct procedure is to connect the ground wire on the recommended manner. Normally lamps do not need to be grounded.
Wiki User
∙ 14y agoThe hot wire is typically the wire that carries the current to the device, in this case the lamp. In most electrical wiring, the hot wire is usually black or red. In your case, since both wires are white, you may need to use a voltage tester to determine which wire is carrying the voltage and is therefore the hot wire.
The two black wires are for the hot connections and should be connected to the brass screws on the lamp holder. The two white wires are for neutral connections and should be attached to the silver screws. Be sure to follow manufacturer instructions and consult a qualified electrician if unsure.
More information is needed as to what device you are connecting to what power supply. The only two identifiable wires are the white and green. In North America the white colour is used for the circuit's neutral and the green is used for grounding of devices.
If the house wiring does not have a white wire, you can cap off the white wire from the track light with a wire nut and electrical tape if necessary. The white wire is typically used as the neutral wire, but if it's not present in your house wiring, capping it off safely will ensure the track light functions correctly with the available black and green wires.
Connect the black wire from the touch sensor to the black wire from the lamp. Connect the grey wire from the touch sensor to the white wires from the post. Connect the brown wire from the touch sensor to the remaining white wire from the lamp. The yellow wire is typically a ground wire and should be connected to the ground wire in the electrical box. Make sure to follow the manufacturer's instructions for proper installation.
You can connect the red wire from the USB cable to the red wire of the two-wire cable. The black wire from the USB cable can be connected to the black wire of the two-wire cable. As for the white and green wires from the USB cable, since the two-wire cable only has a red and black wire, you can leave the white and green wires unconnected as they are not needed in this case. Just make sure to insulate the unused wires properly to avoid any short circuits.
On a 3 wire dryer cord there is no green wire. The white wire coming from the outlet is connected to ground or the green screw. The black and red wires are the hot wires.
The two black wires are for the hot connections and should be connected to the brass screws on the lamp holder. The two white wires are for neutral connections and should be attached to the silver screws. Be sure to follow manufacturer instructions and consult a qualified electrician if unsure.
If you are referring to lamp cord type wire where both wires are brown then yes, connect the wire with the groves to the white neutral and the smooth wire to the black hot wire.
Your black wires are your hot wires. The white is your neutral or common. It would be best to run an equipment ground (green wire) too.
There are probably dozens of black and white wires under the hood. It is a normal color for a ground wire. With out knowing where it or the green wire go, I can not answer.There are probably dozens of black and white wires under the hood. It is a normal color for a ground wire. With out knowing where it or the green wire go, I can not answer.
The red wire is the positive wire. The black wire is the ground wire. The green and yellow wires are the speaker wires. The white wire is the auxiliary wire.
The 1993 BMW 325 radio wiring colors are red, brown, green, yellow, and white. The red wire is the positive wire. The brown wire is the ground wire. The green and yellow wires are the speaker wires. The white wire is the auxiliary wire.
If the house wiring does not have a white wire, you can cap off the white wire from the track light with a wire nut and electrical tape if necessary. The white wire is typically used as the neutral wire, but if it's not present in your house wiring, capping it off safely will ensure the track light functions correctly with the available black and green wires.
The Ford audio wires consist of five different colors. The red wire is the positive wire. The black wire is the ground wire. The speaker wires are green and yellow. The auxiliary wire is white.
The red wire is the positive wire. The black wire is the ground wire. The green and yellow wires are the speaker wires. The white wire is the auxiliary wire.
The black wire is the ground wire. The red wire is the positive wire. The green and yellow wires are the speaker wires. The white wire is the auxiliary wire.
The red wire is the positive wire. The yellow and green wires are the speaker wires. The brown or black wire is the ground wire. The white wire is and auxiliary wire.