0
Depending on how it is wrongly wired, it might appear to work or appear not to work. There is a severe risk of electrocution whenever switches are incorrectly wired. Get an expert to check it and rewire it properly. If this switch is not right, perhaps all the other circuits should be checked too!
I remember my ex-husband "trying" to wire a new light switch in the bathroom. Thinking he knew what he was doing, he tried wiring it like you would a wall receptical.
He routed the hot wire to one end of the switch, and the neutral to the other end. (shows how much he knew)
When he turned the breaker on, and flipped the wall switch, WOW, you should of seen what it did.
The wires literally jumped about 7 inches high near the junction box, there was a loud "thud" and the breaker naturally tripped.
I tried to tell him that you actually split the hot wire that is coming from the breaker box to the light itself and put each an end on each side of the wall switch, and the neutral runs from the breaker to the light and doesn't go near the switch at all.
I told him that it's not the same as a wall receptical, but dummy wouldn't listen.
Add your answer:
Earn +20 pts
Why are lights dim after the switch was replaced?
Dim lights after a switch replacement could be caused by using the wrong type of switch, loose wiring connections, or issues with the electrical circuit. Check that the new switch is compatible with the light fixture, tighten any loose connections, and ensure the circuit is providing the correct voltage. If the issue persists, consider consulting a qualified electrician for further troubleshooting.
Why do dimmer lights not dim?
Dimmer lights may not dim if the dimmer switch is incompatible with the type of light bulb being used. Certain LED and fluorescent bulbs are not compatible with traditional incandescent dimmer switches. It is important to ensure that the dimmer switch and light bulbs are compatible for proper dimming function.
Can you plug your natural gas furnace into a 120 volt receptacle?
The furnace can be but it is not a good idea. Safety code requires a disconnect switch outside the area where the furnace is situated. This switch is used for an emergency shut down in case something electrically goes wrong with the furnace. In modern homes these furnaces are wired to a dedicated 120 volt circuit from the distribution panel. From the panel, the circuit is routed to the safety switch. From the safety switch, the circuit then continues to the furnace load.
When using the remote for a Hunter fan-light the light will not turn on-off using the remote-it will turn on-off using the wall switch but the fan will turn on-off using the remote Any ideas?
If the Hunter fan-light's light is not turning on/off with the remote, it could be an issue with the remote control or the receiver in the fan. Try changing the batteries in the remote control first. If that doesn't work, you may need to reset the remote and receiver by following the manufacturer's instructions. If the problem persists, you may need to contact Hunter customer support for further assistance.
Will it work wired wrong?
No, it will be dangerous. Electricity is very dangerous and installation codes are not written simply to make things work but to make them safe. There are many electrical situations that will work fine even if wired incorrectly. The determination of what is correct or incorrect is what is most safe if something goes wrong. So the question one should ask is not, does it work. But ask the question, If something goes wrong, is this the safest way to have wired this circuit. Only competent electricians who are familiar with and fluent with applicable codes can sufficiently answer this question.
Why did the new light fixture fizzle out when you wired it?
You likely wired it wrong. Not sure what you mean by "fizzle out".
What could be wrong if you replaced an existing ceiling fan with a fan with a light attachment and the fan and remote control work but the light does not although it is wired correctly?
Are you sure the light bulb is good? Perhaps it's not wired correctly even though you think it is, or maybe it's a bad light socket/connection, or a bad switch.
1987 Honda Civic fan sensor wired direct to lights battery dead why?
maybe it's wired on the wrong side of the switch
Why does my light stay on Even though I turn the switch off?
1. THE SWITCH IS BAD 2.THE SWITCH WAS RECENTLY REPLACED AND WIRED INCORRECTLY (POSSIBLE IF THERE ARE MULTIPLE CABLES IN BOX 3.THE CABLE IS SHORTED (UNLIKELY, BUT I'VE SEEN IT) 4.YOU'RE TURNING OFF THE WRONG SWITCH-HA
Why is the protection light on in my car amp?
something is wired up wrong or you overloaded the amp
Radio doesn't work unless headlight switch is turned on?
The radio was wired wrong. Sounds like the hot wire for the radio was connected to the hot wire for the headlight switch.
Can a brake light switch be tested?
yes but i might be wrong
What am I doing wrong when the light switch is off and the light remains on?
you should see a doctor
Why won't your dashboard lights work after installing a new stereo?
you prob touched a bare earth. there is usually separate fuse for dash lights check them all should be a 10 amp fuse I had the same problem what was wrong with me is when it was wired up the person had a wire wired up wrong and everytime i would turn my light on it blew a fuse, check and make sure the wires are wired up right.
What could be wrong if your swimming pool light goes on by itself?
You probably need to replace the light switch
Chevy truck starts but wont turn off?
ignition switch wired wrong . wire from coil hooked to hot post instead of switched post
Just Replaced the factory Radio but dash lights will not dim what did you do wrong?
the iso plug (black connectors) are wired up wrong, it has given the light circuit a constant live
