0
Alkalinity in a boiler is controlled by adding chemicals such as sodium hydroxide or sodium phosphate to maintain the desired pH levels. Monitoring the alkalinity levels regularly and adjusting the chemical dosing accordingly helps to stabilize the pH and prevent corrosion in the boiler system. Regular testing and maintenance are crucial to ensure proper control of o-alkalinity in a boiler.
Add your answer:
Earn +20 pts
Does boiler pressure affect water temperature?
Boiler pressure does not directly affect water temperature. Water temperature is primarily controlled by the thermostat setting on the boiler. However, excessive boiler pressure can lead to other issues such as leaks and inefficiency in heating the water.
Why you need boiler preservation?
Boiler preservation is necessary to prevent corrosion and rust formation when the boiler is not in operation for an extended period. It helps protect the internal surfaces of the boiler from damage and ensures that it can be safely and efficiently restarted when needed. Proper preservation also helps extend the lifespan of the boiler.
If oil is mixed with boiler feed water?
If oil is mixed with boiler feed water, it can cause scaling and fouling in the boiler system, leading to reduced efficiency and potentially damaging the boiler components. It is important to prevent oil contamination of boiler feed water through proper filtration and maintenance of equipment to ensure the smooth operation of the boiler system.
How many amps for a house boiler?
The amp requirement for a house boiler can vary depending on the size and type of the boiler. Typically, a house boiler may require anywhere from 15 to 30 amps to operate efficiently. It is important to consult the boiler's specifications and an electrician to determine the precise amp requirement for your specific setup.
What is an average price for a new natural gas boiler?
The price of a natural gas boiler will depend on a few factors. For example, the company that is selling the boiler, the quality of the boiler and where one is located. Prices may vary depending on location and availability.
Does boiler pressure affect water temperature?
Boiler pressure does not directly affect water temperature. Water temperature is primarily controlled by the thermostat setting on the boiler. However, excessive boiler pressure can lead to other issues such as leaks and inefficiency in heating the water.
What is the advantage of afbc boiler over pf boiler?
afbc has high turn down ratio,burner arrangement is simple,low grade coal can be burnt efficiently,so2 emission can be controlled,
How do you turn up or down a hot water baseboard heater with a oil furnace?
If you are using water and not steam there should be a temperature controller mounted in the side of the boiler, that is where the start and stop point of the boiler is controlled.
Define boiler and classification of boiler?
Boiler can be classified as below
What is the cycle of the boiler?
Cycles are a measure of the dissolved solids in the boiler water in relation to the dissolved solids in the feedwater. For instance, if the measure of chlorides in the feedwater sample is 5 ppm and the chlorides in the boiler water sample is 50 ppm then the boiler water has been cycled ten times, 50/5 =10. That means that all of the water in the boiler (plus all the water that has been blown down) has been evaporated completely ten times, and replaced by the same amount of feedwater. Steam does not carry the dissolved solids out of the boiler, they remain behind, these are controlled with water treatment and a continuous blowdown (bottom blowoffs control or remove suspended solids).
What is afbc boiler?
Atmospheric Fluidized Bed Combustion Boiler (AFBC boiler) is a type of operational boiler. In a AFBC boiler a little more fluidized bed combustor is added than a conventional shell boiler.
How do you lightup afbc boiler?
what is boiler
What is the meaning of cycles in boiler?
Cycles are a measure of the dissolved solids in the boiler water in relation to the dissolved solids in the feedwater. For instance, if the measure of chlorides in the feedwater sample is 5 ppm and the chlorides in the boiler water sample is 50 ppm then the boiler water has been cycled ten times, 50/5 =10. That means that all of the water in the boiler (plus all the water that has been blown down) has been evaporated completely ten times, and replaced by the same amount of feedwater. Steam does not carry the dissolved solids out of the boiler, they remain behind, these are controlled with water treatment and a continuous blowdown (bottom blowoffs control or remove suspended solids).
What is fish boiler?
A fish boiler is a hous boiler that stores fish instead of water.
Where can one find boiler servicing?
There are a number of references to use to find boiler servicing. For example, Service Experts, Inferno Boiler, and Boiler all provide useful information about boiler servicing.
What are the boiler parts and function?
steam boiler
What is Ik pass in a boiler?
An IK on a boiler is a Soot Blow. It is mounted on the sidewall of a boiler furnace and cleans the internal boiler parts with high pressure.
