0
Yes, usually I like to start it with some copper (8 inches) and then attach pex adapters. You can run it directly to it, but it's awkward you're crimping on pex to brass fittings on the tank, it's hard to crimp. If you can manage it, there's nothing wrong with it. It's easier to add a copper nipple first.
What else can I help you with?
Will pex cinch clamp work onpoly?
Yes, PEX cinch clamps are typically compatible with PEX tubing, including PEX-A, PEX-B, and PEX-C. Make sure to use the correct size cinch clamp for the corresponding PEX tubing diameter to ensure a secure connection.
What is the flow rate of water through .75 inch pex pipe at 40 psi in gpm?
The standard formula to calculate flow(GPM - gallons per minute) from a CIRCULAR orifice is:29.7 * (the square root of the pressure) * (the square of the diameter of the flow orifice)EXAMPLE using 3/4" Pex Pipe(actual I.D. of 3/4 PEX Pipe is .677") and 40 PSI pressure:29.7 * 6.325(sq. root of 40) * .458(the square of the I.D. 3/4" pipe) =A GPM of 86.03Note: You also need to account for fittings in the loss calculations; while minimal several fitting will make a difference.
Do I have to insulate pex tubing in below freezing climates?
It may depend on whether or not your pex plumbing is underground (as in a house) or exposed to the subzero air (as in a trailer home). Underground the earth acts as an insulator. Snow piled up against the skirting of a trailer is a very effective insulator. Unfortunately, you can have subzero temperatures without snow, so I would recommend insulation or heat tape in exposed pipes. You may also consider installing a heat source, like a ceramic heater, if you have a trailer. And of course, leave your taps dripping just in case! I have found pex plumbing to be worth the extra cost because although my pipes froze at 20 degrees below, they did not burst. By Linda: I would like to correct a couple remarks above: 1. In underground installations, PEX needs to be installed below the ground freezing level, no matter what the application is. 2. If the tubing is against the exposed wall, the answer is yes, always. You can use split type closed cell foam insulation for such purposes, same as the one used by HVAC contractors.
What does PEX stands for in DU results?
PEX is produced with crosslinked polyethylene. Crosslinking is obtained through a chemical process that increases the bonds between macromolecules to form a more complex structure than the normal polyethylene. Due to the crosslinking, the polyethylene's performance is greatly enhanced still maintaining the excellent properties of thermoplastics. for more details you may visit on this link : http://www.ardipex.com/pex-pipes.php
What is the melting point of pex tubing?
The melting point of PEX tubing is typically around 250-260 degrees Fahrenheit. It is important to note that prolonged exposure to temperatures above its melting point can cause the tubing to deform or break down.
How can I connect PEX tubing to a water heater?
To connect PEX tubing to a water heater, you can use a fitting called a PEX fitting. This fitting is designed to connect the PEX tubing to the water heater securely. Simply insert the PEX tubing into the fitting and use a crimping tool to secure it in place. Make sure to follow the manufacturer's instructions for the specific type of PEX fitting you are using.
How can I connect PEX tubing to a hot water heater?
To connect PEX tubing to a hot water heater, you will need to use a fitting called a PEX fitting. This fitting can be crimped onto the PEX tubing using a crimping tool. Make sure to follow the manufacturer's instructions for the specific type of PEX fitting you are using. Once the fitting is securely attached to the tubing, you can then connect it to the hot water heater using the appropriate connectors. Be sure to check for any leaks before turning on the hot water heater.
Can you connect PEX to a water heater?
No. Not directly. It needs to be 18 inches away... in length, not distance according to the UPC. An 18 inch water heater flex would work or 18 inches of copper tube with a pex adapter on the end will work.
What are the benefits of using PEX piping for a hot water heater installation?
PEX piping offers several benefits for hot water heater installations. It is flexible, making it easier to install in tight spaces. PEX is also resistant to corrosion and scale buildup, which can prolong the lifespan of the system. Additionally, PEX is cost-effective and has good thermal properties, helping to maintain water temperature efficiently.
How can I properly install a PEX sink connection in my plumbing system?
To properly install a PEX sink connection in your plumbing system, follow these steps: Turn off the water supply to the sink. Cut the PEX tubing to the desired length using a PEX cutter. Slide a PEX fitting onto each end of the tubing. Use a crimping tool to secure the fittings onto the tubing. Connect one end of the PEX tubing to the sink's water supply line. Connect the other end to the main water supply line. Turn on the water supply and check for any leaks.
How can I learn how to connect PEX pipes properly?
To learn how to connect PEX pipes properly, you can follow these steps: Cut the PEX pipe to the desired length using a PEX pipe cutter. Insert a PEX fitting into the end of the pipe. Use a crimping tool to secure the fitting onto the pipe. Repeat the process for the other end of the pipe. Test the connection for leaks by running water through the pipes.
What is the process for repairing a leak in the pecs water line?
To repair a leak in a PEX water line, first turn off the water supply. Cut out the damaged section of the PEX pipe using a PEX cutter. Insert a new PEX coupling or fitting to connect the two ends of the pipe. Use a crimping tool to secure the fitting in place. Turn the water supply back on and check for leaks.
What is the best way to connect PEX tubing to copper piping using a PEX to copper adapter?
The best way to connect PEX tubing to copper piping using a PEX to copper adapter is to first cut the PEX tubing to the desired length and then slide the PEX fitting onto the tubing. Next, use a crimping tool to secure the fitting onto the tubing. Finally, solder the copper adapter onto the copper piping and connect the PEX fitting to the copper adapter.
How does PEX supply tubing get connect to city water meter?
for a 3/4" supply use a 3/4" PEX x 3/4" NPT Brass F Adapter
What is the best type of material for water pipe replacement?
PEX is by far the best, long lasting and easy to connect .
How can I connect PEX tubing to copper pipes?
To connect PEX tubing to copper pipes, you can use a fitting called a PEX-to-copper adapter. This adapter has a PEX side that can be crimped onto the PEX tubing and a copper side that can be soldered onto the copper pipe. This creates a secure and watertight connection between the two types of pipes.
How do you connect PVC water line to pex plumbing?
There is a product that is sold at Home improvement stores called "SharkBite". It will allow you to connect Copper,CTS Cpvc and Pex. Here is the link to learn more. Your friend, Matt The Handyman http://www.cashacme.com/prod_literature.php
