0
This is for 2011 Jeep Grand Chrokees with the push-button Start:
- Start with the vehicle off
- With your foot OFF the brake, press the Start button twice (you want to be in the RUN mode, not ACCY, but you're not starting the engine)
- Within 5 seconds, press the accelerator pedal to the floor 3 times, bringing the pedal all the way back up each time.
- Press the Start button once to return to the OFF mode.
That's it! The oil change indicator is reset. Note that if you've disabled the seat belt alarm, you'll have to re-do that sequence too.
Two possible ways: 1. turn the key to run but engine off, then press the gas pedal down three times. Or there might be a red button in the fuse block in the car or in the juction block under the hood.
Turn the key to the on position. Depress the accelerator pedal to the floor 3 times within 5 seconds. Turn the key off, back on and start the engine. it should blink a couple of times and then go off.
take your hot wire off the battery and leave it off for about 15 min. this will give it time to reset. Good luck While sitting in your car turn the key on but do not start the car, press the gas 5 times quickly and return the key to off. This should work
turn the key in the on position without starting it and press down on the gas pedal three times and the change oil light should start blinking
turn the key forward to the on,but dont start it the press the gas petal 3 times and turn switch off the after that start it and see it that helps
Add your answer:
Earn +20 pts
How do you reset the Service 4X4 indicator on a 2006 Jeep Grand Cherokee?
You do not reset it, it is a fault code. It is not a routine maintenance indicator. Fix the problem and the light will go out.
Why does the check gauges indicator keep beeping in a 1996 Jeep Grand Cherokee Oil transmission radiator brake fluids are all measuring ok?
if your refering to the service computer then its probably time for an oil change to reset it after you change oil hit select then set to reset comp to count down the 3000 mile service schedule.
Is there a procedure to reset a 1993 Grand Jeep Cherokee PCM?
Either reset with a scan tool, or by unhooking the battery.
Where is the fuel reset button location on a jeep grand Cherokee?
Where is the fuel reset button on a 2000 jeep Cherokee freedom
What is the Jeep grand Cherokee 2000 reset procedure?
scan tool or unhook the battery.
How do you reset the Service 4X4 indicator on a 2006 Jeep Grand Cherokee?
You do not reset it, it is a fault code. It is not a routine maintenance indicator. Fix the problem and the light will go out.
How to reset service light indicator on 2003 grand Cherokee?
Check engine light is reset with a scan tool.Oil change due is reset by pressing "step" until "0 miles to service" is displayed. Then press and hold "reset" until it resets.
How do you reset the 2005 Jeep Grand Cherokee change oil indicator?
Open your owner's manual. Key on, doors closed. Press "step" until "0 miles to service" is displayed. Press and hold "reset" until it resets.
How do you reset the change oil indicator on your 2002 Pontiac grand am?
Driver side fuse box there is a switch you push to reset.
How do you reset the Performing Service indicator light on a 2002 Grand Cherokee Laredo?
AnswerThe answer can be found in your owner's manual.Key on, engine off.Press "step" until "0 miles to service" is displayed. Press and hold "reset".
How do you reset the Performing Service light indicator on a 2001 Jeep Grand Cherokee?
Key on, doors shut, press "step" until 0 miles to service is displayed, press and hold "reset" until mileage resets.
Why does the check gauges indicator keep beeping in a 1996 Jeep Grand Cherokee Oil transmission radiator brake fluids are all measuring ok?
if your refering to the service computer then its probably time for an oil change to reset it after you change oil hit select then set to reset comp to count down the 3000 mile service schedule.
How do you reset the oil change light on a 2001 Jeep Grand Cherokee?
On your overhead console, hit "Step" until you see the miles to serice. Then you just hold your reset button and it will change to 3000 miles
Where is the fuel reset for 96 Grand Cherokee Laredo?
Jeep does not use inertia/reset switches.
How do you reset the fuel pump on a 2002 Jeep Grand Cherokee?
There is no reset for the fuel pump on a Jeep.
How do you reset the Performing Service light indicator after a maintenance on a 2002 Grand Cherokee?
With the engine turned on and someone in the driver seat. Hit the step button until 0 miles to service appear, hit RESET. A beep will sound and it is done.
How do you reset after an oil change on a 2003 Jeep Grand Cherokee?
Press the step button on the overhead console until the miles to service shows. The hold down reset until it resets.
