The Bear Scout bow is a twin cam bow that can be adjusted for both draw length and draw weight. As the draw length increases so does the draw weight and vise-versa. The draw length and weight is determined by the amount of rotation the cams experience during a full draw cycle. For example, If the cams rotate 270 deg it will have a longer and stronger draw than if the cams only rotate 180 deg. With twin cam bows this rotation is determined by the % of string on each side of the cam. The front side of the cam contains the string that will dead end on the other limb while the rear side of the cam contains the string used to nock the arrow. The scout bow is equipped with cams that allow easy movement of the string back-n-forth from front to rear.
First before adjusting, note the position of the brass nock that is pinched on the string somewhere by each cam. This position is important to remember for adjusting your bow in the correct direction. In order to adjust the rotation of the cams, the bow must be disassembled as stated in manual (push down on limbs and pull cam assembly off). Then unwind the string from the cam. You will notice that the cam can slide along the string. If you want to shorten the draw length and decrease the draw weight, then slide the string so the brass nock is on the front side of the cam. If you want to lengthen the draw length and increase the draw weight, then slide the string so the brass nock is on the rear side of the cam. Then do the same for the opposite cam. Note that the brass nocks must be in the same location on each cam. Then reassemble as stated in the manual. Tada your done and ready to shoot.
I hope this was helpful…
****Answers**** Every bow you should be able to adjust that.
It stands for Multiple draw lengths. You can change the draw length, but you have to provide the modules to do so.
it has a weight lock on it to adjust the poundage you must unscrew the lock then tighten with the desired alan wrench
Draw length is the distance that the string will travel from its original position to your anchor point when you have fully drawn the bow. this will obviously vary for different people. so your draw length will be personal to you. depending on anchor point length of arms etc etc. one way to measure it is to use a stick and place one end on your anchor point and get someone else to measure the length to the tips of your fingers, add one inch for safety
around 49 com
I have a 1989 Browning Accelerator Plus and I was wanting to adjust the draw length?
****Answers**** Every bow you should be able to adjust that.
im at the library
38"
To lengthen the draw on your bear badge bow, you can adjust the bowstring by changing the position of the nocking point or by adjusting the limb bolts, if your bow allows for such modifications. If your bow has adjustable draw lengths, simply follow the manufacturer's instructions to set it to a longer length. Always ensure that any adjustments are made carefully to maintain the bow's integrity and your safety. If you're uncertain, consult with a professional at an archery shop for assistance.
On my Bear Whitetail Hunter there are 3 slots on both the top and bottom pulleys that the cable sits in. One center, and on either side the others are marked with a plus or minus. It is my understanding that you need to put the bow in a press and move the cable position to the desired slots (plus to lengthen, minus to shorten). I am in the process of shortening the draw length of my own. As far as the range of length adjustment or whether both pulleys need to be in the same slots I am not sure. Hope that this helps somewhat. Happy shooting. Jake.
30" is not a draw weight, it is a draw length. It is the length of the draw from the bow to the string when the bow is drawn.
It stands for Multiple draw lengths. You can change the draw length, but you have to provide the modules to do so.
it has a weight lock on it to adjust the poundage you must unscrew the lock then tighten with the desired alan wrench
Impulse XI 53 7/16 on a 28-30 draw length 56 3/8 on a 30-32 draw length
One can find tutorials on drawing a cartoon bear from Youtube, Dragoart, How to Draw Funny Cartoons, Drawing How to Draw, How to Draw Cartoons and many more.
Drawing a bear in a cage can be done many ways. Online there is a variety of how to's to help people draw the item they want. Try looking up a bear and then add a cage.