answersLogoWhite

0


Best Answer

According to the literature, no. The surgery would require removal of part of the fallopian tubes, therefore rendering them useless in getting pregnant. That's why this is a permanent form of Birth Control.

Yes, it can be done and has been by at least two tubal reversal doctors. Check out this URL to see what I mean: http://www.tubal-reversal.net/blog/tag/essure

User Avatar

Wiki User

13y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Can the essure birth control coil be removed?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Music & Radio

What does a Defrost Klixon look like and where is it?

This is located on the outdoor coil. It is usually toward the bottom of the condenser coil and will have 2 wires attached to it. These wires come from the sensor and go into the defrost control board. It is a disc and is easily removed from the coil.


Location of spark plugs in a 2004 Jeep Grand Cherokee limited?

At the top of the engine. The intake needs to be removed to access the plugs on the drivers side. Since there are no spark plug wires, the coil packs need to be removed. The plugs can then be removed and replaced with new ones. See the link below for detailed instructions.


How do you wire 3 single coil pickups 1 volume control and a Gibson style 3-way selector switch in a guitar or where you can find how to?

truth be told you should have a volume and tone control but it's pretty easy to do. go to www.guitarelectronics.com they can show you everything


What Genre is Lacuna Coil?

Lacuna Coil is Gothic Metal.


How do you change spark plugs 2005 jeep grand Cherokee Laredo 3.7L?

Removing plugs - 3.7L engine Each individual spark plug is located under each ignition coil. Each individual ignition coil must be removed to gain access to each spark plug. The coil fits into machined holes in the cylinder head. A mounting stud/nut secures each coil to the top of the intake manifold. The bottom of the coil is equipped with a rubber boot to seal the spark plug to the coil. Inside each rubber boot is a spring. The spring is used for a mechanical contact between the coil and the top of the spark plug. These rubber boots and springs are a permanent part of the coil and are not serviced separately. An o-ring is used to seal the coil at the opening into the cylinder head. 1. Remove necessary air filter tubing at throttle body. 2. Prior to removing ignition coil, spray compressed air around coil base at cylinder head. 3. Depending on which coil is being removed, the throttle body air intake tube or intake box may need to be removed to gain access to coil. 4. Disconnect electrical connector from coil by pushing downward on release lock on top of connector and pull connector from coil. 5. Clean area at base of coil with compressed air before removal. 6. Remove coil mounting nut from mounting stud. 7. Carefully pull up coil from cylinder head opening with a slight twisting action.8. Remove coil from vehicle. 9. Prior to removing spark plug, spray compressed air into cylinder head opening. This will help prevent foreign material from entering combustion chamber.10. Remove spark plug from cylinder head using a quality socket with a rubber or foam insert. Also check condition of ignition coil o-ring and replace as necessary.Installing plugs - 3.7L engine Special care should be taken when installing spark plugs into the cylinder head spark plug wells. Be sure the plugs do not drop into the plug wells as electrodes can be damaged. Always tighten spark plugs to the specified torque. Over tightening can cause distortion resulting in a change in the spark plug gap or a cracked porcelain insulator. 1. Start the spark plug into the cylinder head by hand to avoid cross threading. 2. Tighten spark plugs to 20 Ft. lbs. torque. 3. Before installing ignition coil(s), check condition of coil o-ring and replace as necessary. To aid in coil installation, apply silicone to coil o-ring. 4. Using compressed air, blow out any dirt or contaminants from around top of spark plug. 5. Position ignition coil into cylinder head opening and push onto spark plug. Do this while guiding coil base over mounting stud. 6. Install coil mounting stud nut.7. Connect electrical connector to coil by snapping into position. 8. If necessary, install throttle body air tube.3.7L engine coil

Related questions

What happens if your Mirena coil is left in for 6 months more when its expired?

If you leave in Mirena after it's expired, you could get pregnant. Use an alternate method of birth control. If you are seeking pregnancy, have the IUD removed.


What if your essure coil falls out?

You need to contact your Dr and be checked to make sure if fell out and didn't get lodged someplace else in your body.


When can a woman stop using birth control?

whenever she is ready to... When a woman wants to get pregnant she can stop Birth Control. For older woman the Coil IUD can sometimes be a better alternative to the pill.


What are some effective products for birth control?

There are many effective products and techniques for birth control. The most effective and popular is the contraceptive pill. Also available are condoms, the coil and the cap.


What does a Defrost Klixon look like and where is it?

This is located on the outdoor coil. It is usually toward the bottom of the condenser coil and will have 2 wires attached to it. These wires come from the sensor and go into the defrost control board. It is a disc and is easily removed from the coil.


The process of preventing fertilization of eggs is called?

The process of preventing fertilization of eggs is called contraception or birth control. Examples of contraception include the birth control pill, Depo Provera injection, the coil and condoms.


What can you use to control a Tesla coil?

Coil lightings are sporadic.


Do you need to remove the coil spring to replace the upper control arm bushing on 1990 dodge ram van?

I have a '96 and I know they changed some things, but to my knowledge it's not necessary. I've completely removed my upper control arms without touching the coil springs. The coil spring goes from the lower arm to the frame, and the upper only connects to the steering knuckle.


How much water is removed if 10000 CFM enters the coil at?

The amount of water removed when 10000 CFM enters a coil depends on the specific humidity of the air and the coil's efficiency in removing moisture. To calculate the exact quantity of water removed, you would need to know these factors and apply them to the heat transfer principles governing the coil's operation.


How do you install a pickup coil on a 96 GMC sierra V8?

96 gmc does not have a pick up coil but the coil is monted to the intake removed by two bolts pick up is in the dis. removed by pulling the dis. then by taking a part


Where is the coil wire on a 1995 Buick Riviera?

There is no coil wire. There is a coil pack and connected to the coil pack is the ignition control module.


How long must you wait to get pregnant after removing an IUD?

After Mirena is removed, you can expect your hormones and period to return to its previous pattern within 4-6 weeks. Like the birth control pill, Mirena gets out of your system quickly once removed.