0
Turn off the player, hold down the function button until it turns on taking you to a menu letting you set the time etc.
Keep pressing the function until you get to the aux option, turn it on by pressing the up key.
Then start the unit and press the mode button, you should now have CD, Tuner and Aux available.
:-)
Still curious? Ask our experts.
Chat with our AI personalities
Taiga
Judy
BlakeAdd your answer:
Earn +20 pts
How do you keep mosfet from overheating i use only mosfet and control it using variable resistor it works but it gets overheated and brokedown.My battery operated scooter is 24v dc 72 amp.thank you.?
Use a mosfet driver instead of a simple resistor. Using a resistor to control the mosfet is a bad idea anyways because you will have terrible control (mosfets are voltage controlled. Take a look at the response curve for your mosfet). If your mosfet is fully on, its ratings may be too low for continuous operation or the power dissipation is too low for the transition between off an on an that is killing your mosfet.
What are the differences betweeen e-mosfet and d-mosfet?
An e-mosfet is and "enhancement" mosfet. A d-mosfet is a "depletion" mosfet. These essentially show what mode the mosfet operates in when a voltage is applied to the gate. . An enhancement mode mosfet is normally non-conducting but conducts when the channel is enhanced by applying a voltage to the gate and pulling carriers into the channel. A depletion mode mosfet normally conducts but becomes more and more non-conducting as carriers are depleted or pulled out of the channel by applying a voltage. The polarity of the voltage depends on whether it is an N channel or P channel. P channel uses positively doped silicon while N channel uses negatively doped silicon. N channel fets are used wherever possible because N material conducts better than P material. There are basically two types of fet, the jfet and the mosfet. The jfet uses a single junction to control the channel hence draws some current. Bipolar transistors use two junctions. In the mosfet (Metal Oxide Semiconducting Field Effect Transistor) there is no such junction hence draw so little current for control purposes it can be regarded as zero. The gate is isolated from the channel by a very thin layer of metal oxide (usually chromium dioxide). An enhacement mode mosfet can be turned on by applying a voltage then removing the wire to the gate. The channel will then remain conducting for some time.
What is the advantages of mosfet?
Advantages:- 1- mosfet are small compare to bjt's so it fabricated easily and space saving scheme on the ic's 2- mosfet's input impedance are very high so they do not load the circuits. loading effect doesn't arise. 3- operating frequency is very high so may be used at higher frequencies. 4- used in digital circuits for it's reliability. 5- effect of noise is less than bjt. so high signal to noise ratio. 6-mosfets are unipolar devices so reverse saturation current doesn't exist. 7- it consume less D.C power rather than BJT. Disadvantages:- handling is not easy- Mosfet is very sensitive to electrostatic charge so it may be destroy when you touch the pins of a mosfet devices by hand. trans conductance is low than BJT.
Can you use the aux on your remote to control your dish box?
You can but it will only work in IR mode. I have provided instructions on how to program the remote to the AUX button. These instructions will only work with the 722 and 922. It is also used only if you want 1 remote to control 2 different receivers.Program Remote to Receiver > via Aux ModeYou can use one DISH Network remote to control two different receivers. The second receiver must be programmed into the AUX mode, and will only operate the receiver in IR.1.Press the SYSTEM INFO button on the front panel of your receiverThe "System Info" screen should display2.Press and hold the AUX mode button on your remoteAll four mode buttons should light up3.Press 3 and then enter a number between 1 and 15, using the number pad on your remoteThe AUX button should light up4.Press the POUND (#) buttonThe AUX button should flash 3 times5.Press the RECORD buttonIf the steps are successful, the number entered in Step 3 should display on the "System Info" screen6.Select "Done"Thanks.
What is the best dj equipment being used by top dj's?
Best equipment in terms of CD players industry standard is Pioneer! Best equipment in terms of Mixers industry standard is Allen & Heath/Pioneer! Most popularly adapted computer interface Serato/Tracktor Bests Amps , Speakers not defined as all speakers provide different things for example specfic tweeking to suit your use.
