answersLogoWhite

0

This technique works well with minute punctures. The bare essentials to perform this operation are a small sachet of super-glue(per leak), like Feviquick, and a disposable syringe (its a good idea to by a second in case the glue.

First pump up the Basketball until it is relatively firm. Now immerse the ball in a half-filled bucket of water (half-filled so the water doesn't come splashing down all over you), making sure that all of the ball is completely below the surface. Locate all the leaks by the stream of bubbles emerging from the surface of the ball. Encircle and cross the leak(like a cross-hair)( using a permanent marker (contrasting colour) or a ball point pen, if you don't mind the tiny marks on your ball, as this will help locate the leak quickly.

Now you may release the part of the air from the ball (using the nozzle provided with your basketball) to make sure that air is no longer emerging from the puncture.

This is the tricky part. The next few steps must be executed quickly so its best you read this part through before attempting the following....

BE VERY CAREFUL HANDLING THE SYRINGE. DO NOT ACCIDENTALLY INJECT YOURSELF OR ANYONE ELSE WITH THE SUPER GLUE AS THE CONSEQUENCES COULD BE LETHAL. IF YOU CHOOSE TO PERFORM THIS OPERATION MAKE SURE YOU DO IT IN THE PRESENCE OF ANOTHER ADULT, AS A PRECAUTIONARY MEASURE, WHO IS IN A POSITION TO FETCH HELP IN CASE OF ANY EMERGENCY.

Open your sachet/bottle of super glue and dip the needle of the syringe into the glue itself. Draw the glue into the syringe and make sure there aren't any air bubbles.

Now locate the leak, which you have marked with the marker pen and insert the needle through the skin. Let the syringe be inserted up to half its entire length. Now turn the ball until your syringe is dangling underneath the ball itself. At this point, inject a tiny amount of super glue into the ball while keeping the ball above the syringe itself. Carefully removed the syringe from the ball and apply a couple of drops of super glue to the punctured area on the outer surface. Do not apply too much here as the glue will tend to spread and solidify unevenly ruining the appearance of the ball.

Keep the ball in the same position (with the puncture directly at the bottom) for a period of time until the super glue dries completely.

Repeat the process for each of the leaks, one at a time. Use multiple syringes (a syringe can rarely be reused after it has drawn super glue as the glue solidifies inside) to repair multiple punctures.

After this step, you may now pump up the ball and repeat the immersion test to see if all the leaks have been properly sealed. If yes, then you are ready to play ball. If not, then its most likely you injected the super-glue in the wrong spot or were too careless with the ball's position while injecting the glue.

In theory, the super-glue instantly binds with the material inside the ball forming an airtight crust. The excess glue pools around the puncture, while a certain amount trickles into the air passage of the leak itself. This created a sort of board-pin like structure that proves to be quite sturdy and is also complimented by the increased air-pressure once the ball is properly pumped. The glue on the outer surface reinforces the punctured region preventing the passage from reopening in the near future.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How can one repair a workout ball with a small hole?

One can try to repair a workout ball with a small hole by removing the air of the ball and then carefully filling the hole with glue made for balls. Then one can fill the ball with air again.


What is the best way to repair a small hole in a wood floor?

To repair a small hole in a wood floor, you can use wood filler or putty to fill the hole, sand it down to make it smooth, and then apply a matching stain or finish to blend it in with the rest of the floor.


Can you repair a small hole in a fiber pool without letting the water out?

Yes you can!


What does it mean when you have a small hole on your waterline?

A small hole on your waterline could indicate a leak in the water pipe. It is important to investigate and repair the hole to prevent water damage and potential mold growth. Consult a plumber to properly address the issue.


How can I effectively repair a small hole in drywall?

To effectively repair a small hole in drywall, you can follow these steps: Clean the area around the hole and remove any loose debris. Apply a small amount of spackling compound or joint compound to fill the hole. Smooth the compound with a putty knife and let it dry completely. Sand the area to make it smooth and blend it with the surrounding wall. Apply primer and paint to match the rest of the wall.


How do you repair a scraped basketball?

purchase a new basketball


How do you repair a hole in the muffler on your 91 Chevy s10 truck?

If there is a rotted hole in the muffler please replace the muffler. However, if there is a small hole at the bottom end of the muffler it is there to allow water to escape.


How can I repair a small hole in drywall effectively?

To repair a small hole in drywall effectively, you can follow these steps: Clean the area around the hole and remove any loose debris. Apply a small amount of spackling compound or joint compound to fill the hole. Smooth the compound with a putty knife and let it dry completely. Sand the area to make it smooth and blend it with the surrounding wall. Prime and paint the patched area to match the rest of the wall.


Will a small piece of rusted rebar continue to cause problems in a hole in the shallow end of an in ground pool after the hole has been filled with waterproof cement during an underwater repair?

It sounds like the repair should work if done properly.


If you cut a hole in a basketball what happens to the gas inside?

If you cut a hole in a basketball, the gas inside will slowly escape through the hole. This will eventually cause the basketball to lose its inflation and become deflated.


How can you repair a hole in your Wavemaster XXL base?

Most plastic 'glues' will melt the plastic enough to fill in a small hole. You may want to supplement it with another piece of plastic.


My 2001 ford ranger oil pan has a small hole in it how is the best way to repair it?

The proper and most reliable way of making that repair would be to replace the oil pan.