0
Bunsen burners are preferred over candles or fires because the Bunsen burner produces a much higher temperature (noted by the blue flame) and it is much easier to contain/control a Bunsen Burner flame.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What to note of when using Bunsen burner?
dont burn things
What is a Bunsen burner and what is its function?
The bunsen burner is used to heat items for experiments using a controllable temperature flame and surface area at which the heat is applied to the vessel.
How do you be safe using a Bunsen burner?
how to be safe using a Bunsen Burner:1. never leave the flame unattended... especially when on the blue flame.2. always wear safety glasses.3. don't heat up anything metal because they will get very hot.4. don't let young children near the Bunsen burner when it's on.5. always have someone watch it.6. turn the gas off immediately when the flame goes out.
When you are not using a Bunsen burner but wish to leave the flame on you should always leave the air hole closed why?
It is less hot
Safety proceedures using the Bunsen burner?
Step one: Place the Bunsen burner on a heat proof mat Step two: Check that the rubber tubing is connected properly to the Bunsen burner and the gas tap. step 3: ensure that the air hole is closed Step 4: Light the math Step 5: Open the gas tap Step 6: Hold the burning math over the barrel. Make sure your hand is not in the passage of the flame.
Can you melt iron using a Bunsen burner?
No, a Bunsen burner does not produce enough heat to melt iron. Iron has a high melting point of around 1538°C, which requires a much hotter heat source, such as a furnace or a specialized industrial equipment.
What to note of when using Bunsen burner?
dont burn things
How can you make a Bunsen burner hotter?
By using the correct ratio of oxygen and fuel mixture. Opening the air hole in the Bunsen burner increase the oxygen which helps the flame burner hotter .
Why is it safer to evaporate alcohol using an infra red heater rather than using a Bunsen burner?
The Bunsen burner uses an ope flame, making it easier for the alcohol to ignite.
Why did Robert Bunsen lose an eye?
Robert Bunsen lost an eye due to a laboratory accident. While working with cacodyl cyanide, a highly toxic and volatile compound, the substance exploded and caused severe injury to his eyes. This accident led to the loss of his left eye.
What is a Bunsen burner and what is its function?
The bunsen burner is used to heat items for experiments using a controllable temperature flame and surface area at which the heat is applied to the vessel.
How do you combine the Bunsen burner to the LP gas cylinder?
There will be a valve at the bottom of the Bunsen burner. Using a rubber tubing connect the valve to the regulator of the LPG cylinder.
How much time is required to melt sodium chloride using Bunsen burner?
The time it takes to melt sodium chloride using a Bunsen burner can vary based on factors such as the heat intensity of the burner, the amount of sodium chloride being melted, and the starting temperature of the salt. Generally, it may take a few minutes to melt sodium chloride completely using a Bunsen burner.
Why must you never blow your Bunsen out like you would blow out a candle?
Blowing out a Bunsen burner can result in a sudden burst of flame due to the build-up of gas. This can be dangerous and cause injury. Instead, the Bunsen burner should be turned off using the stopcock to stop the gas flow, then safely cooled down before storing.
Why tip a Bunsen burner at an angle when using?
contaminates will be less likely to drip inside the burner this way
What is the purpose of a candle burner?
A candle burner, also known as a candle warmer is an electric warmer that melts a candle to release its scent. The advantages of using a candle warmers is the soot that often results from burning wax.
What colour should the flame be on the Bunsen burner when you are not using it?
The flame on a Bunsen burner should be blue when not in use. If the flame is yellow, it may indicate a problem with the burner, such as not enough air mixing with the gas, which can be a safety hazard.
