Best Answer

When calculating the torque you would use the lenght of which ever tong that is connected to your load cell.

Q: When applying make up torque to drill pipe with 2 different tong lengths which tong do you calculate the make up torque with?

Write your answer...

Submit

Still have questions?

Continue Learning about TV & Celebs

Between 1600 and 2100 ft/lbs., depending on the engine.

I think the Rod “Torque” Redline (American Spy Car) is none other than aDodge Challenger.....

I assume you mean a newton metre(N.m) Which means in the International System of Units (SI), a newton meter is known as a unit of torque. It can also be used as a unit of energy, this is known in the SI as a Joule.

There are many derivations of the eccentric cam, but the basic principle is consistent. The cam itself may be round, elliptical, semi-conical, or irregularly shaped to increase or reduce workload at different points of its rotation. The one constant of an eccentric cam is that the pivot point is NOT located the geometric center of the cam. Sometimes the cam is used in conjunction with a "cam follower". Probably the best known example of this is the cam shaft of an automobile. The "lobes", or high spots on the cam, lift rods (the cam followers) that open the valves of the engine. Another use of an eccentric cam is in a pulley type system. In this system the cam acts like power-torque converter. In other words, it changes the power required to rotate the cam. The math for explaining how this works is fairly complex and is best explained using calculus, so for brevity I will explain with an example. Gently roll a boiled egg end over end on a smooth surface. You will notice that it speeds up and slows down as it goes through the rotations. As the egg rolls to the tip it slows down. As the egg continues to roll past the tip, it speeds up. Then it slows down again and then speeds up. This is how an eccentric pulley works as well. As the "lobe" or thick side of the pulley rotates to the center stress point of the cable, the work required is greater. Once the center of the lobe passes the center of the stress point of the cable the work becomes easier. One of the best known applications of this system is a compound archery bow. Drawing the bow is hard because the lobe must be pulled between the stress point of the string and the pivot point. Once the bow is drawn, the lobe has passed the stress point of the string. Holding the bow drawn is easy because upon release the string needs to pull the lobe back between the stress point and the pivot point. I hope this helps.

Lightning McQueen , Harv , Mack , Lightning McQueen's pit crew , Rusty and Dusty Rust-eze , Strip Weathers , Lynda Weathers / Mrs. The King , Tex Dinoco , Mater , Chick Hicks , Sally Carrera , Sheriff , Doc Hudson , Ramone , Luigi , Guido , Sarge , Flo , Fillmore , Lizzie , Red , Frank and Stanley .

Related questions

what is the torque on the head bolt and sequence for a ford 3000 diesel engine.

how to calculate hydraulic motor torque

Measure the rpm & calculate the torque as power divided by angular velocity

how to calculate hydraulic motor torque

To calculate brake torque, multiply force with the distance from the point of rotation. Force is equal to the torsional reaction caused by the brakes, and is also equal in magnitude to the torque exerted by the road.

how calculate power gearbox output

By applying the same force farther from the center of rotation.

If the precessionnal motion is caused by applying gravitational torque,it is called gyroscopic motion.

If you know the torque, you can calculate the HP.

Torque is defined as force multiplied by the distance, from the axis of rotation, at which such as force is applied.In the case of an engine, I believe the torque would have to be measured.

without specifying the force its not possible to find the torque.

Torque is the measurement of turning force. A wrench applies torque to a bolt. A motor or engine provides torque to do work. Horsepower is the measurement of the work done or ability to do work. This is done by taking the speed the engine is operating at (RPM) and what torque it is producing and applying a formula to give a horsepower rating.