answersLogoWhite

0

What else can I help you with?

Related Questions

Why is infinity chosen as the reference for measuring potential?

Infinity is chosen as a reference for measuring potential because it represents the maximum possible value in a scale. By setting infinity as a reference point, it allows for relative comparisons to show how other values or quantities measure up in relation to the greatest possible extent. This makes it easier to understand and analyze the potential of other values in comparison to infinity.


How do you measure the inches by inches?

Inches are usually measured with a ruler, or by using some other type of length measuring instrument.


What is a semi-infinite medium?

One-dimensional example: A semi-infinite medium is a medium that extends to infinity in one direction but has an end in the other direction


How to get centimeters on the measuring tape?

You can buy many tapes with inches on one edge and metric on the other.


Why an odd-degree function must always have at least one real root?

An odd-degree function approaches positive infinity in one direction and negative infinity in the other direction so the graph must cross the x-axis at least once, giving it at least one real root.


What is a line a segment and a ray in math?

A line is a one-dimensional set of points that extends to infinity in both directions (so it has no endpoint). A ray is a line that goes to infinity in only one direction and has one endpoint. A line segment is a line with two endpoints (so it does not go to infinity).


If a right triangle has one side measuring 3 inches and the other side measures 4 inches what is the measure of the hypotenuse?

Using the Pythagorean triple 3, 4, 5 we say that the hypotenuse is 5 inches.


What are lines line segments and rays?

The three differ in their extent. Lines are infinite in both directions. Line segments are finite: they have two well defined end-points. Rays are finite in one direction, infinite in the other: it has one end-point and stretches to infinity in the other direction.


Can a triangle with a 4 inch side have a 55 and 35 degree angle?

A triangle with 1 side only measuring 4 inches can have two of its angles measuring 55° and 35°. The side would be either the hypotenuse or one other other sides of a right angled triangle. NOTE : A triangle with two of the three sides measuring 4 inches cannot have one of its angles measuring 55° and one other measuring 35° as the two sides of equal length would define it as an isosceles triangle. Therefore two of its angles are equal. If the two equal angles measured 35° each, then the third angle would equal 110°. If the two equal angles measured 55° each then the third angle would equal 70°. A triangle with all three sides measuring 4 inches has all three angles measuring 60° . It is an equilateral triangle.


What was the applications of galvanometer?

Galvanometers were used for measuring small electric currents in early electrical instruments, as well as for detecting the presence and direction of current flow in circuits. They were also used in the development of instruments like voltmeters, ammeters, and other measuring devices in electrical engineering.


How do you convert a distance of 14 degrees 54 minutes and 36 seconds into meters?

The short answer: about 1664850 meters. [14*60+54+36/60] = 894.6 minutes of arc * 1861= 1664850 m I assume you are measuring angular distance on the surface of the Earth. Now that will depend on the direction and the latitude that you are measuring If you are measuring directly North -South then it doesn't matter and the answer would be almost identical to if you were measuring along the equator (East- West). But if you are measuring anywhere else or in any other direction then it depends from where and in what direction. (Think that the full circle of 360 degrees in an East West direction is only a little over 30 meters if you start 5 meters from the North OR South Pole yet 40 000 000 meters at the equator.


What comes before inches?

In the context of measurements, the unit that typically comes before inches is feet. The imperial system of measurement commonly used in the United States and other countries includes feet and inches as units for measuring length. For example, a measurement might be given as 5 feet 6 inches, where feet precedes inches in the measurement.