answersLogoWhite

0

Reference points: Think about how the part will be made, and how it will be inspected. Usually something will make sense. Try to keep common references between drawing views, and if possible try to base everything from points, planes, or edges that appear in multiple views.

Tolerances: Consider how the part will be made- what minimum tolerances can be held on the intended equipment and processes? What is the maximum tolerance on the individual parts that will allow the assembly to fit together and function properly? The right answers lie between those extremes.

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Engineering

Identify the types of water heating systems available in srilanka and analyze the selection criteria for different forms of water heating systems and equipments?

Solar and tankless


How embedded systems are used in navigation?

It is used to identify the persons location and to direct persons to other specific direction.


What types of disk arrays provide the MOST fault tolerance?

RAID 6 provides the most fault tolerance of any standard RAID disk arrays (RAID 0, 1 , 5, 6, and RAID 10). If any two disks in a RAID 6 array fail and are removed, then two new blank disks can be installed and no data has been lost. RAID 1+1 or most other "layered" RAID systems can provide more fault tolerance than RAID 6, tolerating the failure of any 3 disks. Some experimental non-standard disk arrays can provide more fault tolerance with less overhead, such as the parchive system. Nearly all distributed file systems and distributed version control systems can be set up so that if one machine is completely destroyed by fire, all the data can be recovered from a backup machine in another building.


What is an analog address?

An analog address is a reference point used in analog systems to identify specific locations or values within a continuous range, such as voltage levels or physical positions. Unlike digital addresses, which represent discrete values, analog addresses can vary smoothly and can represent an infinite number of states. They are commonly used in applications like analog signal processing, where signals vary continuously over time.


What is the short names for the project systems?

Short names for project systems often include acronyms or abbreviated terms specific to the industry or organization. Common examples include PS for Project Systems in SAP, PPM for Project Portfolio Management, and WBS for Work Breakdown Structure. These abbreviations facilitate easier communication and reference among project stakeholders.

Related Questions

How do you identify workpiece reference points and systems of tolerancing?

Workpiece reference points can be identified through established design specifications, which often include key features such as edges, holes, or surfaces that serve as datum points. Systems of tolerancing, such as Geometric Dimensioning and Tolerancing (GD&T), provide a framework for defining the allowable variations in the dimensions and geometry of the workpiece. By utilizing these reference points and tolerancing systems, manufacturers ensure proper fit, function, and interchangeability of components in assembly. Proper identification and application of these principles are crucial for maintaining quality control in manufacturing processes.


What is a bibcode?

A bibcode is an alphanumeric code used in astronomical data systems to identify a specific literature reference.


Types of distributed systems with reference to hardware softwareoprating systems and scalability?

this is the systems harddrive that makes the operating system work


Identify the systems that a non government organization of your choice needs or could use?

Systems


What are the imperial and metric systems of measurement tolerance and fixed reference points?

The imperial system of measurement, primarily used in the United States, employs units such as inches, feet, and pounds, with tolerances often expressed in fractions of these units. Tolerance in this system typically refers to the permissible limit of variation in a physical dimension. The metric system, used globally, is based on units such as meters, liters, and grams, with tolerances defined in decimal form, often using prefixes like milli- or centi-. Fixed reference points in both systems are established standards, such as the meter for metric and the yard for imperial, ensuring consistency and accuracy in measurements.


How many type of question answer system are there?

There are three types of online Q&A systems, digital reference systems, expert systems, and social Q&A systems.


Monitor systems and work activities of Tesco organization?

Monitor systems and work activities of your organization and identify the major problems effecting the systems. Also identify the opportunities your company can avail to improve business process.


Opsec used to identify?

adversary intelligence systems


Opsec is used to identify?

adversary intelligence systems


What is the 3 levels of damage tolerance?

The three levels of damage tolerance are typically categorized as primary, secondary, and tertiary. Primary damage tolerance refers to structures designed to withstand loads without significant damage, ensuring safety and integrity. Secondary damage tolerance allows for some damage to occur while still maintaining functionality and structural stability. Tertiary damage tolerance involves systems that can endure significant damage and still operate, often relying on redundancy or backup systems to maintain safety and performance.


What do you mean by non genetic resistance and how it is acquired?

Tolerance is acquired by compensatory mechanisms in the endocrine and nervous systems.


How do you identify national policies and local systems that relateto safeguarding and protection from abuse?

Identify national policies and local systems that relate to safeguarding and protection from abuse