Length of the slab in which the houdry blocks are facing ( hadder face) divide by two will give you ans the substract 1 from the ans ...[ l/2=ans - 1 ]
In order to estimate rcc roof slab you must measure the roof and calculate its area. Then you must contact a professional to see how much slab will be needed.
That's sort of a strange question. A concrete slab is a horizontal surface -- it's meant to be a surface you stand on or build things on. Concrete blocks are usually used for vertical surfaces -- walls. I believe that poured concrete walls are more expensive than concrete block walls. You wouldn't use concrete blocks as a substitute for a concrete slab.
Slab area multiply 1.4 times.
To protect buildings against heat loss through a concrete roof slab, you can use insulation materials installed above or below the slab. Rigid foam insulation or spray foam can be applied directly to the underside of the concrete to minimize thermal bridging. Additionally, incorporating a reflective or radiant barrier can further reduce heat transfer. A diagram would typically illustrate the layered structure, showing the concrete slab, insulation layer, and roofing materials on top.
Different types of Slabs :1. Conventional solid slab:-- the slab which is braced with beams and columns is called conventional slab this kind of slab is small whereas the depth of the beam is large and load is transferred to beams and from beams to columns. These types of slabs are used in constructing Floors of multi stored building. It is of two types.a) One-way Slab.b) Two Way Slab.2. Flat Slab:-Flat slab is a reinforced concrete slab secured directly by concrete columns or caps .flat slab doesn’t have beams.3. Waffle slab:- Waffle slab is a reinforced concrete roof or floor containing square grids with deep sides. This kind of slab is majorly used at entrance hotels, malls, restaurants
To calculate hourdi blocks in a slab, first determine the total area of the slab you need to cover. Then, find the area of a single hourdi block, which typically has standard dimensions. Divide the total slab area by the area of one hourdi block to get the number of blocks required. Additionally, consider adding a percentage for wastage and cuts during installation.
The Hourdi slab, also known as the "Hoardi slab," is a type of flooring system commonly used in construction, particularly in regions with limited resources. It consists of lightweight clay or concrete blocks that are placed on beams, creating a ribbed structure that enhances strength while minimizing weight. This system allows for efficient thermal insulation and reduces the amount of concrete needed, making it a cost-effective solution for building floors. Hourdi slabs are especially popular in Mediterranean and Middle Eastern architecture.
In order to estimate rcc roof slab you must measure the roof and calculate its area. Then you must contact a professional to see how much slab will be needed.
1. one way slab 2. two way slab 3. flat slab 4. roof slab
The minimum covering of reinforcement for roof slab is 30mm
M20
V of a circular slab = thickness of the slab multiplied by (pi multiplied by the radius2)
One DIY method to lift a concrete slab is by using a jack and some wooden blocks. Place the jack under the slab and slowly raise it by pumping the jack. Insert wooden blocks under the slab as it lifts to support it at the desired height. Be cautious and ensure the slab is lifted evenly to prevent cracking or damage.
That's sort of a strange question. A concrete slab is a horizontal surface -- it's meant to be a surface you stand on or build things on. Concrete blocks are usually used for vertical surfaces -- walls. I believe that poured concrete walls are more expensive than concrete block walls. You wouldn't use concrete blocks as a substitute for a concrete slab.
Multiply the length by the breadth. eg if slab is 2 ft by 3 ft then area of slab = 6 sq feet
The number of cover blocks used in one square meter of slab typically depends on the spacing of the reinforcement bars (rebars) and the size of the cover blocks. Generally, cover blocks are placed at intervals of about 1 meter apart along the length and width of the slab. For a standard 1-meter square slab, you might use approximately 4 to 8 cover blocks, depending on the specific design and spacing requirements. Always consult structural guidelines or an engineer for precise calculations based on your project's needs.
Slab area multiply 1.4 times.