0
you put your water in the bursen burner then put in on heat the heat should be moderate to avoid vigorous boiling.Alway take note that you do not make the mouth of the bursen burner to face you put it the opposite side and do not lok in side the bursen burner.
Place a heat-resistant container filled with water on a heat-proof mat over the Bunsen burner flame. Adjust the air hole on the Bunsen burner to control the intensity of the flame and heat the water until it reaches a rolling boil (bubbling vigorously). Be cautious when handling hot materials and always use proper protective equipment.
Add your answer:
Earn +20 pts
How long does it take to boil 50 ml of water using a Bunsen burner?
It typically takes around 2-3 minutes to boil 50 ml of water using a Bunsen burner, depending on the intensity of the flame and the efficiency of the burner.
How long does it take to boil ml of water in a Bunsen burner?
8.30 minutes
How long does it take to boil 150ml of water on a Bunsen burner?
It typically takes around 2-3 minutes to boil 150ml of water on a Bunsen burner, depending on the intensity of the flame and the efficiency of the burner.
What kind of flame takes longer time to boil water using Bunsen burner?
A yellow flame would take longer to boil water using a Bunsen burner compared to a blue flame. This is because the yellow flame is cooler and provides less heat energy for boiling water.
When you boil a beaker of water over a Bunsen burner will it become a gas?
No, when you boil a beaker of water over a Bunsen burner, the water will not turn into a gas. It will reach its boiling point (100°C at sea level) and turn into steam, which is the gaseous form of water.
How long does it take to boil 50 ml of water using a Bunsen burner?
It typically takes around 2-3 minutes to boil 50 ml of water using a Bunsen burner, depending on the intensity of the flame and the efficiency of the burner.
How long does it take to boil ml of water in a Bunsen burner?
8.30 minutes
How long does it take to boil 150ml of water on a Bunsen burner?
It typically takes around 2-3 minutes to boil 150ml of water on a Bunsen burner, depending on the intensity of the flame and the efficiency of the burner.
What kind of flame takes longer time to boil water using Bunsen burner?
A yellow flame would take longer to boil water using a Bunsen burner compared to a blue flame. This is because the yellow flame is cooler and provides less heat energy for boiling water.
At what height above the iron ring did the water boil the soonest on a Bunsen burner?
The water will boil the soonest at the highest point because heat rises, so the heat from the Bunsen burner will be concentrated at that point.
When you boil a beaker of water over a Bunsen burner will it become a gas?
No, when you boil a beaker of water over a Bunsen burner, the water will not turn into a gas. It will reach its boiling point (100°C at sea level) and turn into steam, which is the gaseous form of water.
How long does it take to boil 100 ml of water in a Bunsen burner?
8.30 minutes
Which metal can you boil from a Bunsen burner?
You can boil mercury from a Bunsen burner. Mercury has a low boiling point of 674 degrees Fahrenheit, making it possible to vaporize it using a Bunsen burner's high heat. However, it's important to note that working with mercury can be hazardous, so proper safety precautions should be taken.
What Bunsen burner flame do you use to boil water?
For boiling water, you would typically use a medium to high, blue, non-luminous flame on a Bunsen burner. Adjust the air hole to achieve the desired intensity of the flame.
What is the uses of Bunsen burners?
A Bunsen Burner, is piece of equipment particularly used in a science lab. The Bunsen Burners creates a gas flame which is used to assist in experiments. The Bunsen burner originating from 1852, given the name by Robert Bunsen.
How long does it take to boil 50 ml of water using a burner?
No more than a few minutes.
Can you boil water in a test tube suspended in a pot of water?
Yes, you can boil water in a test tube suspended in a pot of water using a Bunsen burner or a heat source. The water in the pot will transfer heat to the test tube, causing the water inside to boil. Make sure to handle the test tube carefully to avoid breakage and use appropriate safety precautions.
