0
What else can I help you with?
How do you convert a natural gas space heater to propane?
Converting a natural gas space heater to propane involves replacing the gas orifices, adjusting the air-to-fuel ratio, and installing a regulator designed for propane. It is important to follow the manufacturer's guidelines and have a professional technician perform the conversion to ensure proper and safe operation of the heater.
What is the size of the orfice hole for a natural gas heater?
The size of the orifice hole for a natural gas heater typically ranges from 0.014 to 0.036 inches, depending on the specific model of the heater. It's important to refer to the manufacturer's instructions or consult a professional for the correct specifications for your heater.
What is the appropriate water heater breaker size according to the water heater breaker size chart?
The appropriate water heater breaker size is determined by the water heater's wattage and voltage, as indicated in the water heater breaker size chart. It is important to match the breaker size to the specifications of the water heater to ensure safe and efficient operation.
What size map is a 175000 is considered to be?
A map scale of 1:175,000 means that 1 centimetre on the map represents 175,000 centimetres on the ground.
What size space heater would fit in a living room or bedroom?
The size of a space heater depends on the size of a living room or bedroom. The best size for a space heater is 150 sq. ft for living rooms and bedrooms.
What size is a map with a 175000 scale?
On 1:175,000 scale map one cm on the map represents 175,000 cm or 1.75 km (~1 mile).
What size wire should be used for a hot water heater?
The size of wire needed for a hot water heater depends on the heater's wattage and the distance from the electrical panel. It is recommended to consult a professional electrician to determine the appropriate wire size for your specific hot water heater.
What size is 175000 map?
On 1:175,000 scale map one cm on the map represents 175,000 cm or 1.75 km (~1 mile) in the real world.
What size gas piping should you use for installing a pool heater?
Need more info. How long a run from the gas meter to where the heater will be? How many BTU heater? The longer the run and the larger the heater size then the larger the pipe size. Ken Also one should know the heating value of the fuel as natural "gas" can be as low as 900 BTU per cu ft to 1,200 BTU per CU ft You should also know the BTU OUT put of the heater. One should take the normal ambient temperature the volume L x W x H of the water to be heated and have n idea what the desired temperature of the water they are seeking 06/15/2013 (a) One needs to know whether this is a Natural Gas Appliance, or a Propane Appliance. ( Natural Gas is Low Pressure so needs greater volume < larger pipe>) (b) w' Propane heater, run galvanized nipple from gas valve direct out of casing to 2nd stage Regulator. Include a "Drip T" to retrieve moisture. ( pipe size dictated by the thread on the gas valve. No restictions beween Regulator except an inline shut off valve. Include a Union inside the cabinet so you can remove and service burner tray if needed. (c) w' Natural Gas utilize the manufacturer's specs . Also A Manometer is an essential tool to check the inlet (static) gas pressure, and the valve open pressure to ensure sufficient gas flow to avoid "Sooting Up" the heat exchanger with a "lazy" flame ( gas starved ). All pool heater manufacturers will provide their install specs. Call them and ask. Always SOAP TEST all connections. Immediately after install prior to igniting the device, and again after running appliance ( heat can cause joint expansion).
What size water heater for 3000 square foot home?
what size water heater for 3000 sq ft 4 bathroom house
What is the average room size that any average heater works best at?
About 100 square feet is the averge room size for a heater to be used.
What size of breaker to use on a wall unit 220 heater?
The size of the breaker needed for a 220V wall heater depends on the current rating of the heater. Generally, for a 220V heater, a 20-amp breaker is common. However, it's important to check the manufacturer's specifications and local electrical codes for the appropriate breaker size.
