While it is not exact these settings will provide a general guide when applying powdered or pelletized lime using most Scotts Spreaders. Please note we always suggest testing the pH level prior to an application of lime, to ensure that it would be reuqired and it takes roughly 40#-50# per 1,000 sq ft of lime to change the pH of the soil 1 level. and it can take up to 6 months for the change to occur in the soil.
Turf Builder Drop Spreaders/AccuGreen/Scotts metal drop (including PF models) spreader:
Basic/
Turf Builder
Deluxe/
Turf Builder
EdgeGuard (Mini and DLX)/Standard/LP Standard/SpeedyGreen/EdgeGuard:
EasyGreen spreader:
Spreader settings for Scotts manufactured spreaders are listed on the back of the bag.
The spreader setting for Scotts Southern Turf Builder when using the EZ Broadcast spreader by Republic is 3.5. If you are using the EZ Drop Spreader by Republic the spreader setting is 6.5.
For a drop spreader 7, broadcast 5
If you send an email to Scotts Consumer service they can actually send you the spreader settings you need. You can contact them through their website and they will email your spreader setting. https://www.scotts.com/smg/contactus/contactUs.jsp?navId=page900108&parentId=page900134
The Scott drop spreader PF3 is designed for residential lawn care, ideal for applying fertilizers, seeds, and other granular products. Its setting typically involves adjusting the spreader to the appropriate setting based on the type of material being used and the desired application rate. The spreader is suitable for various lawn sizes and is built for ease of use on flat terrains. Always refer to the specific product guidelines for optimal settings.
The settings for an ortho drop spreader typically depend on the type of material being applied, such as fertilizer, seed, or herbicide. Generally, you can adjust the flow rate by turning the dial or lever on the spreader to the recommended setting indicated on the product label. It's important to calibrate the spreader according to the manufacturer's guidelines for even distribution and to avoid over-application. Always check the specific instructions for the material you're using for the best results.
The setting for a EZ Drop Spreader by Republic at a rate of 3.4 lbs per 1,000 sq ft would typically be found in the spreader's manual or on the calibration chart. Generally, for this rate, you might expect to set the spreader at a medium to high setting, depending on the specific model and the type of material being spread. It's important to conduct a test run to ensure even distribution and adjust the setting as needed for optimal results. Always check the manufacturer's guidelines for the most accurate settings.
While it is not exact these settings will provide a general guide when applying powdered or pelletized lime using most Scotts Spreaders. Please note we always suggest testing the pH level prior to an application of lime, to ensure that it would be reuqired and it takes roughly 40#-50# per 1,000 sq ft of lime to change the pH of the soil 1 level. and it can take up to 6 months for the change to occur in the soil.Turf Builder Drop Spreaders/AccuGreen/Scotts metal drop (including PF models) spreader:10# per 1000 sq. ft. - Setting of 11.530# per 1000 sq. ft. - Setting of 1240# per 1000 sq. ft. - Setting of 15.550# per 1000 sq. ft. - Setting of 17.5Basic/Turf BuilderDeluxe/Turf BuilderEdgeGuard (Mini and DLX)/Standard/LP Standard/SpeedyGreen/EdgeGuard:30# per 1000 sq. ft. - Setting of 1040# per 1000 sq. ft. - Setting of 7.5, go over the area twice50# per 1000 sq. ft. - Setting of 7, go over the area three timesEasyGreen spreader:10# - Setting of 2830# - Setting of 27, go over the area three times40# - Setting of 27, go over the area four times50# - Setting of 27, go over the area five times
When setting the Scotts Standard Broadcast Spreader for lime pellets, it is important to refer to the manufacturer's recommendations for the specific product being used. Generally, lime pellets are larger and heavier compared to grass seed or fertilizer, so a higher setting on the spreader may be required to ensure proper coverage. It is recommended to start with a conservative setting and make test passes in a small area to determine the appropriate setting for even distribution of the lime pellets.
While it is not exact these settings will provide a general guide when applying powdered or pelletized lime using most Scotts Spreaders. Please note we always suggest testing the pH level prior to an application of lime, to ensure that it would be reuqired and it takes roughly 40#-50# per 1,000 sq ft of lime to change the pH of the soil 1 level. and it can take up to 6 months for the change to occur in the soil.Turf Builder Drop Spreaders/AccuGreen/Scotts metal drop (including PF models) spreader:10# per 1000 sq. ft. - Setting of 11.530# per 1000 sq. ft. - Setting of 1240# per 1000 sq. ft. - Setting of 15.550# per 1000 sq. ft. - Setting of 17.5Basic/Turf BuilderDeluxe/Turf BuilderEdgeGuard (Mini and DLX)/Standard/LP Standard/SpeedyGreen/EdgeGuard:30# per 1000 sq. ft. - Setting of 1040# per 1000 sq. ft. - Setting of 7.5, go over the area twice50# per 1000 sq. ft. - Setting of 7, go over the area three timesEasyGreen spreader:10# - Setting of 2830# - Setting of 27, go over the area three times40# - Setting of 27, go over the area four times50# - Setting of 27, go over the area five times
A broadcast spreader is used to spread seed, fertilizer or sand over a large area. It is commonly used on farms and is an alternative to using a drop spreader.
It's on the bag