answersLogoWhite

0


Best Answer

#02-03-99-002: Service Air Suspension Message Diagnostic Trouble Code (DTC) C0711 and/or Clicking Noise From Rear of Vehicle with Ignition Off and/or Electronic Controlled Air Suspension (ECAS) Compressor Cycles Too - (Nov 26, 2002)

Models:2003 HUMMER H2with Off Road Suspension Package (RPO ZM6)

DTC C0711

Diagnostic Instructions

DTC C0711 00: Level Control Air Pressure Sensor Circuit

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Air Suspension Pressure Sensor 5-Volt Voltage Reference

C0711 00

C0711 00

C0711 00

--

Air Suspension Pressure Sensor Signal

C0711 00

C0711 00

C0711 00

C0711 00

Air Suspension Pressure Sensor Low Reference

--

C0711 00

--

--

Circuit Description

The air suspension pressure sensor sends a voltage signal to the air suspension control module that corresponds to a pressure within the range of 30-180 psi. The air suspension control module also uses this signal to verify that the proper amount of pressure is achieved in the air dryer within 23 seconds prior to opening of the inlet valves for inflation of the air springs.

Conditions for Running the DTC

Battery voltage is between 9-16 volts.

Conditions for Setting the DTC

The air suspension module detects that the supplied 5-volt reference voltage circuit for the pressure sensor falls below 4.75 volts or exceeds 5.25 volts.

The air suspension module detects that the signal voltage circuit for the pressure sensor falls below 0.5 volt or exceeds 4.75 volts.

Action Taken When the DTC Sets

• The air suspension system will be inoperative.

• The SERVICE SUSPENSION SYSTEM message will be displayed.

Conditions for Clearing the MIL/DTC

• When the fault is no longer present, DTC C0711 will change from a current DTC to a history DTC on the next ignition cycle.

• DTC C0711 will be cleared from history after 50 ignition cycles.

Diagnostic Aids

Repair all other DTCs before C0711.

This DTC is set when:

• The pneumatic status of the air suspension system is out of limits.

• When excessive amounts of time have elapsed when inflating the air springs.

• When there is a air leak in the system.

• When vehicle speed is greater than 3 km/h (1.8 mph) and rate of height change is out of limits which may be caused by a damaged LR or RR air suspension sensor.

• When the underhood fuse block 60A compressor fuse (ECAS fuse) is open.

• When the compressor relay is defective.

• When there is an intermittent or permanent loss of continuity between the compressor and the compressor supply voltage during an upwards leveling event.

DTC C0660 Level Control Exhaust Valve Circuit Malfunction

User Avatar

Wiki User

13y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What is the repair for code c0660 and c0711?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you change 'check engine Code' on 1995 Dodge Spirit?

Yo can not "change" an engine code. You need to repair what is causing the code.Yo can not "change" an engine code. You need to repair what is causing the code.


How do you reset the 4x4 service light on a 2001 dodge durango?

You need to have the code read and repair the cause.You need to have the code read and repair the cause.


ICD-9 code for status post hernia repair?

The ICD-9 code for status post hernia repair is V55.1. This code is used to indicate a history of surgery for hernia repair.


How do you repair error code p1601 on a Mazda mpv 1996?

how do I repair error code p2009. show image of part involved


How do you reset the ABS light of your Chrysler 300?

You have to repair the malfunction that caused the code stored in the abs computer.You have to repair the malfunction that caused the code stored in the abs computer.


What is the anesthesia code for ventral hernia repair?

the code is 00830


How do you get your car out of limp mode?

Repair the code deficiency and cancel the code.


How do you repair a code P1409 on a Ford Escape?

The repair code P1409 on a Ford Escape is for the EVR Control Circuit. You will need to replace the circuit.


How do you fix a dct companion code that was set in both the ecm and pcm?

Either the PCM, or ECM will have another code in it. Diagnose and repair that code and the companion dtc set code will go away.Either the PCM, or ECM will have another code in it. Diagnose and repair that code and the companion dtc set code will go away.


What is the code for plastic repair of a urethrocele?

57230


What is the cpt code for repair of complete atrioventricular canal?

cpt code 33670


How to Fix Error Code 30015-12?

Open Control Panel using Start. Click on Programs and select Programs and Features. Select Quick Repair and click on Repair. If Quick Repair didn't fix the error code 30015, select Online Repair and click on Repair.