answersLogoWhite

0

Well, I just figured out why my Toro Weedwacker wouldn't run, The fuel hoses were backward, My brother had it for a while then told me it stopped running. He apparently tried to FIX it but accidentally reversed the fuel lines so.
1. Fuel comes out of the tank and goes directly into the bottom of the Carb,
2. Fuel is pulled through the carb from the side tube on the carb into the priming bulb.
3. Once the priming bulb is full the fuel is then returned directly to the tank through a hose which protrudes into the tank about 2 ".
4. Ran fine after I got the hook up correct.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

Where is the in and out a primer bulb?

The "in" and "out" markings on a primer bulb indicate the direction of fuel flow. The "in" side typically connects to the fuel tank or line bringing fuel to the bulb, while the "out" side directs the fuel towards the engine or carburetor. Properly connecting these lines ensures the primer bulb effectively primes the fuel system for starting. Always refer to the specific equipment's manual for accurate installation guidance.


What is the fuel line routing for a primer bulb?

The fuel line routing for a primer bulb typically involves connecting the fuel line from the fuel tank to one side of the primer bulb, and then connecting another fuel line from the other side of the primer bulb to the carburetor. The primer bulb acts as a manual pump that helps to draw fuel from the tank into the carburetor to aid in starting the engine. It is important to ensure that the fuel lines are properly connected and free of any kinks or blockages to ensure proper fuel flow.


A diagram for fuel lines for a poulan woodshark 1950?

Make sure you have the lines wright the skiney line from in the tankgoes to the top nipple on the carb the over flow line goes to the long nipple on the primer bulb and the other line off the primer bulb goes to bottom nipple on carb


How do you replace fuel lines and primer bulb on a snapper s31sst?

To replace the fuel lines and primer bulb on a Snapper S31SST, first, ensure the engine is off and cool. Disconnect the old fuel lines from the carburetor and fuel tank, taking note of their routing. Remove the old primer bulb by detaching it from the lines and install the new bulb, ensuring proper orientation for fuel flow. Finally, attach the new fuel lines, ensuring they are secure and free of kinks, and reconnect everything before testing for leaks.


Are winds named for the direction they flow to or the direction they flow from?

Winds are named for the direction they flow from. For example, a northeast wind comes from the northeast direction.


In which direction does the river shannon flow?

in which direction does the river Shannon flow?


How do you drain fuel tank 2004 Yamaha XLT 800 Waverunner?

Disconnect the input side of the "fuel water separator" (Fuel filter) take that hose and connect it to another long 1/4 inch hose with a primer bulb on the other end. Get the primer bulb lower than the gas tank of the jetski and start the flow by squeezing the bulb. Make sure you have the jetski gas selector in the "RES" position to get as much out as possible. Once it starts flowing gravity should do the rest. It's not fast but it works.


Do you prime the engine after your snowblower runs out of gas?

Yes, you should prime the engine after your snowblower runs out of gas, especially if it has a primer bulb. Priming helps to draw fuel into the carburetor, making it easier to start the engine again. After running out of gas, it’s important to refill the tank with fresh fuel and allow the primer bulb to fill the carburetor before attempting to start the snowblower. This ensures proper fuel flow and smooth operation.


What direction do fluids flow?

Downward, Downriver, Downhill, the direction gravity pulls everything.


Why does gas pour out when you prime your snow blower?

Its most likely going to be your carb. The needle and seat can be sticking and allowing fuel to flow all the time as opposed to when it is needed. Try to get a rebuild kit for the carb and try it again.


How does a electric current flow through a light bulb?

The electrical current comes into the bulb from the metal side,flow through the filament ,and out the tip.


What additional factor will be change if the direction of a current flow is change?

direction of magnetic field