0
If it is one of the brake lights on either side of the tailgate, there are only two screws that hold it on. Let the tailgate down & you will see them on the side. Remove these two screws (one in plain sight, one kind of hidden around in the tailgate cable area), & the tail light assenby will come out. There are three bulbs in the tail light assembly & they're all the same type, even the reverse light bulb (type is 3057). You should probably replace these with LED's since they don't burn out like bulbs do, just make sure you get the right ones. The bulb sockets will rotate about 1/4 of a turn (can't remember which way) & should then easily slide out.
What else can I help you with?
How do you replace the rear brake light bulb on a 2004 Honda Civic?
How do you replace the rear brake light bulb on a 2001 Honda civic?"
Where is the fuse for brake lights located for 2004 jeep liberty?
w to replace center brake light in 2004 jeep liberty
How do you replace rear window brake light bulb on 2004 Hyundai Santa f e?
How do you replace rear window brake light bulb in the 2004 Hyundai Santa Fe?Read more: How_do_you_replace_rear_window_brake_light_bulb_on_2004_Hyundai_Santa_f_e
2004 F250 Brake lights not working but everything else does?
replace brake light switch located on brake pedal under dash
How do you replace 3rd brake light on the Mercedes e class 2004?
To replace the third brake light on a 2004 Mercedes E-Class, first, open the trunk and remove the trim panel covering the brake light assembly. Disconnect the electrical connector and remove the screws securing the brake light. Replace the old light with the new one, reattach the screws, and reconnect the electrical connector before replacing the trim panel. Test the light to ensure it functions properly.
How do you shut off ABS light on 2004 Nissan Frontier?
I just had this problem on my 98 Frontier because the brake lights were staying on. I had to replace the brake light switch and the brake light button for it to go out.
How do you replace third brake light 2004 Mitsubishi endeavor?
To replace the third brake light on a 2004 Mitsubishi Endeavor, first, open the rear hatch and locate the cover for the brake light assembly. Remove the screws securing the cover, then gently pull it away to access the bulb. Twist the old bulb counterclockwise to remove it, replace it with a new bulb, and reassemble the cover by securing it with screws. Finally, test the new brake light to ensure it’s functioning properly.
How do you change a brake light on a 2004 LS?
WHICH brake light?
How do I replace brake light on 2004 Isuzu Axiom?
To replace the brake light on a 2004 Isuzu Axiom, first, open the rear hatch and locate the tail light assembly. Remove the screws or clips holding the tail light in place and carefully pull it out. Disconnect the wiring harness, then twist the bulb socket counterclockwise to remove the old bulb. Replace it with a new bulb, reassemble the tail light, and ensure it’s securely fastened before testing the brake lights.
How do you replace brake light switch on 2004 jeep?
To replace the brake light switch on a 2004 Jeep, first disconnect the negative battery terminal to ensure safety. Locate the brake light switch, which is typically mounted on the brake pedal assembly. Remove the electrical connector from the switch, then unscrew the switch from its mounting location. Install the new switch by securing it in place, reconnecting the electrical connector, and finally reconnecting the battery.
How do you change brake light on Acura RSX 2004?
To change the brake light on a 2004 Acura RSX, start by opening the trunk and removing the access panel on the side where the brake light is located. Twist the bulb socket counterclockwise to release it, then pull out the old bulb and replace it with a new one. Finally, reinsert the bulb socket, twist it clockwise to secure it, and replace the access panel. Test the brake lights to ensure they are functioning properly.
How do you replace brake light on 2004 Kia Sedona?
Remove the tail light assembly cover in the cargo compartment. Take hold of the brake light connector. Push the connector in and turn at the same time. Do the same with the brake lightbulb. Reverse the process to install the new brake lightbulb.
