answersLogoWhite

0

A few trailer spindles bolted on to the axle but most spindles are welded to the axle.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

How do you change the front axle on a 1998 Honda civic?

jack up car remove wheel remove axle nut take bottom 19mm bolt loose and 14mm loose from horseshoe remove horseshoe separate spindle from lower ''a'' arm pull Axle out of spindle remove from trans to replace reverse process


How do you replace drivers side axle on a 2002 Saturn coupe?

Drain tranny fluid. Remove 30mm nut on axle end. remove brake caliper and disconnect tierod from spindle. Turn spindle all the Right. Pull axle from spindle. Then use a pry bar to remove it from the tranny. Be carefull NOT to damage the axle seals. Pry against the metal case of the tranny. It will just pop out. Installation is reverse


How do you remove front spindle on jd 4430?

To remove the front spindle on a John Deere 4430, first, ensure the tractor is securely supported and the front axle is raised. Remove the wheel and tire assembly, then detach the steering linkage and any hydraulic lines connected to the spindle. Next, unbolt the spindle from the axle housing, and gently tap it out if necessary. Finally, inspect for wear or damage before reinstalling or replacing the spindle.


What do you need to do to remove and replace a passenger axle on a 91 pont6000le fwd?

Raise car securely, remove wheel, brake calipher and brake rotor. Remove the bolts on the inner part of the axle where is bolts to the transaxle. Place jack under lower control arm and then separate lower arm from spindle by removing the nut on the lower ball joint. Remove the axle nut and pull the spindle out from the axle while pushing the axle thru it. Reverse procedure. I hope this helps you. Mark


How do you change a front wheel bearing assembly in a Nissan Murano?

remove wheel,unbolt caliper assembly,remove rotor,take off axle nut and push in axle as far as it will go in,remove abs sensor attached to spindle,remove 4 bolts behind spindle attaches hub bearing. hammer out bearing . reverse to install


How do you remove cv joint on 2003 buick regal?

Easy enough. jack up front end and support remove wheel remove brake caliper and pads and caliper bracket remove rotor, bang/pry off if necessary loosen axle nut, flush to end of axle remove the tie rod end that sits in the spindle(don't touch the jam nut on rack side) swing tie rod/rack arm aside tap end of axle bolt to loosen axle in housing remove axle nut and swing/push spindle to one side while pulling axle out the other installation is the reverse


How do you remove a CV axle on a 93 Ford Probe?

It really isn't hard but you need direction. Get a manual on your car from AUTOBOOKSONLINE.COM Jack up the car and place jack stands under a solid area Peen the safety lock on the axle nut with a hammer an chiesel Remove the axle nut with a strong impact gun and a 1 1/4" socket Remove the brake caliper & hang it with a tie wrap Remove the brake shoe housing Remove tie rod from spindle Remove the ABS wire harness clip in strut Remove the 2 strut bolts with a 17mm socket and wrenches Remove lower ball joint locking bolt Swing down spindle assembly and remove axle assembly from outer splines Knock out axe from transmission side Note: If axle is seized in hub, spindle assemble must be removed with axle attached and then heated and removed.


How do you change a front axle on a 2002 Pontiac grand prix?

Take the tire off remove the axle nut remove the pinch bolt and remove the ball joint from the spindle Push the end of the axle through the spindle"center of brake rotor" that might require a hammer and punch, be careful not to ruin threads carefully pry the axle from transmission, this may take some force while holding the axle and moving the rotor/spindle out of the way, pull the axle out reverse to install, making sure to properly torque all bolts and nuts to the recommended specs. failure to do so can result in an accident. Use thread lock on the ball joint pinch bolt for added safety.


How do you change c v joints 1989 topaz?

do not remove strut bolts instead take lower balljoint loose ,take axle nut loose pulling spindle out as you push in on axle, then pry axle out of trans


How do you replace a 1999 Oldsmobile Silhouette front axle bearing and hub assembly sensor?

First remove wheel and brake caliper and rotor. Unplug wheel speed sensor wire. Remove axle nut. Remove three 1/2 inch head bolts from back side of spindle. Gently tap hub to remove hub/bearing assy. from spindle. Installation is the reverse.


What is the maximum trailer axle weight allowed in UK?

In the UK, the maximum axle weight for a trailer axle on a 6 axle trailer is 8500 kg. In addition it must have road friendly suspension. With a 5 axle vehicle the maximum axle weight is 11.5 tonnes.


How do you repare a broken axle?

Front wheel drive: Jack up the car and put on stands. Block the rear wheels. remove wheel remove caliper and suspend from frame work do not let it hang there. Remove axle nut. Remove nut and bust loose lower ball joint. Move spindle out of the way and pull axle assembly from the transmission. Buy replacement axle and reverse above procedure