0
for any auto repair, consult your repair manual. if you do not have the required tools, manuals or knowledge to complete the repair then you need to consult a certified mechanic.
any mess-ups that you make while doing your own mechanical work can be catastrophic. engine parts must perform their job up to 100 times per second, and anything that is installed incorrectly can cause bad performance or even system failure, possibly damaging other components and increasing repair costs.
What else can I help you with?
How do you change the ignition switch in a 1988 Chevy Camaro?
How do i change the ignition switch in a 1988 Chevy camaro
1988 jeep wrangler runs while cranking quits when you let off?
you have an open circut in your ignition switch change your ignition switch.
How do you install ignition switch 1988 gmc truck?
You need to remove the steering wheel first with a puller. There is a latch you can trip with a small screwdriver that will let the ignition switch slide out. Simply replace the switch and put the steering wheel back on.
How do you change or fix an ignition switch on a 1988 Corsica when the key turns but does not actuate anything?
If your 1988 Chevy Corsica key only turns in the ignition and does not start the automobile, it is probably unfixable. Remove the ignition switch retaining ring. Slide the out and remove the wiring harness. Reverse the process to install the new ignition switch.
How do you change ignition in 1988 Chevrolet s10?
To change the ignition on a 1988 Chevrolet S10, first disconnect the negative battery cable to ensure safety. Remove the steering column cover by unscrewing the screws, then locate the ignition switch, which is typically mounted on the steering column. Disconnect the wiring harness and remove the ignition switch by unscrewing it. Install the new ignition switch by reversing the steps, reconnect the wiring harness, and reattach the steering column cover before reconnecting the battery.
How do you change the ignition in a 1988 Chrysler New Yorker?
To change the ignition in a 1988 Chrysler New Yorker, first disconnect the battery to ensure safety. Remove the steering column cover by unscrewing the screws and carefully prying it off. Next, locate the ignition switch, disconnect the wiring harness, and remove the ignition switch from its mounting. Finally, install the new ignition switch by reversing the steps, ensuring everything is securely connected before reassembling the steering column cover and reconnecting the battery.
How do you remove the ignition switch in a 1988 Isuzu pickup?
how to remove lock cyliner switch 1988 Isuzu pickup
How do you install key ingition switch 1988 Chevy S-10?
how do install key ignition switch 1988 Chevy s10
How do you repair the ignition system on a 1988 Jaguar xj6 that will not turn off the engine and does not kill power feed to dash?
sounds like u need to change the ignition switch itself ( the keybarrel)
1988 dodge D-100 ignition switch linkage adjustment?
To adjust the ignition switch linkage on a 1988 Dodge D-100, first, ensure the vehicle is in the "Off" position. Remove the steering column cover to access the ignition switch and linkage. Loosen the mounting screws for the ignition switch, adjust the linkage until it aligns properly with the ignition cylinder, and then retighten the screws. Finally, reassemble the steering column cover and test the ignition switch for proper operation.
How do you change the ignition control module in a 1988 Chevy Silverado 5.7 L?
How do you change the ignition control module in a 1988 Chevy Silverado 5.7L
How do you remove the ignition switch on 1988 ford bronco?
To remove the ignition switch on a 1988 Ford Bronco, first disconnect the battery to prevent any electrical shorts. Next, remove the steering column covers by unscrewing the screws holding them in place. Then, locate the ignition switch, disconnect its wiring harness, and remove the mounting screws that secure it to the column. Finally, carefully pull the ignition switch out of the column.
