0
Depends on vehicle & state. You may need to have ready monitors and there may be a minimum amout of ready monitors varying by model, year and state. There must also be no DTC's. Best way to make monitors ready is take a nice long car ride for about 20 miles and do not disconnect battery at all.
What else can I help you with?
How do you reset periodic inspection of proton suprima s?
To reset the periodic inspection reminder on a Proton Suprima S, you typically need to locate the inspection reset function in the vehicle's onboard computer system. This can usually be done through the infotainment system or dashboard settings. If you're unsure, consult the owner's manual for specific instructions or visit a Proton service center for assistance. Always ensure that the vehicle's inspection and maintenance are up to date before resetting any reminders.
How do you reset the computer on a 98 Honda Civic that failed inspection due to a not ready message?
Your vehicle's OBD system collects data while you are driving and uses it later to determine if your vehicle passes the OBD emissions test. In some cases, the computer cannot collect enough data and indicates it is "not ready" to provide test results. This can occur if repair work was performed or the battery was disconnected recently. It normally takes at least a week of combined highway and city driving for the computer to complete its systems check and be "ready" for the OBD test. If a vehicle fails because of an emissions problem, it needs to be repaired and pass a re-test at the same inspection station within 60 days of the initial test. For vehicles that are "not ready," the OBD system was unable to complete its systems check for the OBD test. This is usually due to recent repairs or a recently disconnected battery. Usually, at least a week of combined highway and city driving will reset the OBD system so that it will be "ready" for the OBD test. If your vehicle is still "not ready" at the re-test, the inspector will give you a notice explaining that additional driving is required to reset system monitors. After 60 have days have passed, you will need to pay an additional fee for each subsequent OBD test.
How many miles do you have to go to reset your OBD system on your 2001 Buick?
0 once you press erase on your scanner or the shop presses it it is reset as for when the sensors get all the info they need to say ready it is usually about 3 days of my normal driving
How do you reset service inspection on a vw polo?
To reset the service inspection on a VW Polo, turn on the ignition without starting the engine. Press the accelerator pedal three times within 10 seconds, then turn off the ignition. When you restart the car, the service indicator should be reset. If it doesn't reset, you may need to consult the owner's manual or a professional for assistance.
How do you reset the computer on a blazer?
i have been told if y try to start the vehicle anywhere from 1 to 100 times it will reboot itself if you are trying to reset for an inspection you need a computer to plug into your ecm if you un-hook the battery it will only show up at the inspection station
To pass inspection how many miles after check engine light has been reset to you need to drive?
50 to 100 miles
How do you reset a Panasonic home theater system?
all we need is the model of the system.
Does the computer need to be reset after replacing the ignition system?
A computer should not have an ignition system.
How do you reset the engine service light on a 98 Ford Escort?
Unplug the battery for 15 mins will reset the check engine light, but watch will reset all your sensors to. Personal experience it will not read for at least 100 miles, so dont do it when you need an inspection
How do you start your 2006 grand prix if the theft deterrent system is on?
The system will need to be reset or repaired. To reset a original GM system start by using the remote lock and unlock the doors. Then have a repair shop scan the computer and see if it can be reset. If that does not work it will need to see a GM dealer or qualified repair person.
How do you turn inspection light off 2005 polo?
To turn off the inspection light on a 2005 Volkswagen Polo, you typically need to reset the service indicator through the vehicle's dashboard. Start by turning the ignition key to the "on" position without starting the engine. Then, press the accelerator pedal three times while holding down the trip reset button. This should reset the inspection light. If the light remains, consult your owner's manual for specific instructions or consider a visit to a mechanic.
Manual for mss3000?
need to find the reset code for mss3000 alarm system
