0
Add your answer:
Earn +20 pts
Can a 200 amp automatic transfer switch be used with a 100 amp service?
Answer for USA, Canada and countries running a 60 Hz supply service.No. The ampacity of the transfer switch is rated at 100 amps. What this means is that the manufacturer of the switch states that the mains, breakers installed are all rated for a maximum of 100 amps. What can be done, is to install a 100 amp breaker in the 200 amp service and use the output of the breaker to feed into the line side of the automatic transfer switch. The load side of the ATS will be a sub panel that have your preferred loads that you want to stay on during a power failure.This said, it is a complicated job in as much as you have to know wire sizes, ampacity of wires and proper electrical workmanship. Such a project should be left to a licensed electrical contractor to take out the proper permits and call for proper inspections. By taking this route it will leave you confident that if any mishaps happen to the installation down the road your insurance company will be behind you 100%.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Do you have to program a new transfer case control module on a 1999 suburban?
I had a transfer switch mode switch fault on My 1999 suburban and it would not shift out of 2 wd. I put an new switch in and it did not help. I purchased a new transfer case control module from the dealer for $230. The guy behind the counter did not think I needed to have it programed but suggested I ask the service manager. The service manager told me that it would not work until I spent the $100 to have them program it in the car. I put it in and went trough the 5 times ignition off and on and pull and replace the fuse sequence to wake up the module. It started up and is working perfectly. I am glad I tried it without going back to the dealer.
Why is the service 4wheel drive light on 03 silverado?
99 times out of 100 the switch on the dash has failed, replace it first.
What is a good option for a generator that can put out 100 kW everyday and be easily hooked up to a house?
Your specifications of the equipment need to be stated. Voltages and amperage of the generator. Whether the house needs to be on a transformer from the generators output. Is the house now on utility power and you want the generator to be switched to standby power. Automatic transfer switch or manual transfer switch. A 100 kW generator seems pretty big to operate for just a home. Generator engines (prime mover) like to be operated at close to maximum output and a half loaded generator will not make the engine work hard enough. The generator has to be sized to the load. There are too many variables to give a complete answer. If you go to the discussion tab and open a dialogue I will be glad to discuss this with you.
Will a Generac RTSW100A1 100-A Indoor Automatic Transfer Switch work on a 10KW Centurion generator?
Yes. The output of your generator will be about 42 amps.Installation of this transfer switch is an area where a wrong connection could go very wrong with devastating results.It is a complicated job in as much as you have to know wire sizes, ampacity of wires and proper electrical workmanship. Such a project should be left to a licensed electrical contractor to take out the proper permits and call for proper inspections. By taking this route it will leave you confident that if any mishaps happen to the installation down the road your insurance company will be behind you 100%.See related links below.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energizedIF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Price of 380 simi-automatic pistol?
Semi-automatic pistols can vary from 100-1000.
How many watts does a switch use?
A typical Ethernet switch averages around 5-25 watts of power usage, depending on the number of ports and the data transfer rate. However, more advanced and higher-capacity switches can consume up to 100 watts or more.
What would cause a 1995 F150 4WD to work in low range but not in high range?
Possibly bad transfer case. If a GM compact (T) truck, consider a bad 4x4 switch. If an Explorer you might have a bad contact plate, replace the encoder motor. Because your transfer case might be shot it could be the bearings..auto locking? get manuals, it costs 100 and u need to get out, but it won't fail you. if electronic 4x4 switch, you need a new switch if manuel linkages, adjust linkages
What is the value of a Sega 410 Semi Automatic Rifle?
It is a semi automatic shotgun. 100-400 USD or so
2003 350z automatic 0-60 and 0-100?
if you have automatic 350z and you know how to take off in it you should do about 5.8-6.0 sec to 0-100 about 13 or so.
What is the value of your 100-cal 308 semi-automatic rifle windchester?
100-300 or so
What does a 12ga mosberg automatic cost?
100-450 USD
