0
What else can I help you with?
What is the wiring diagram for a 1976 f-250 from ignition module to distributor and from module to key source?
Here is the wiring diagram:
Your 1986 Chevy Celebrity has no spark but new distributor rotor wires and plugs it turns over but wont start please help?
Possible reasons why you have no spark: Bad ignition module Bad pickup coil Bad engine control module Wiring issues
Is the engine control module covered on power train warranty for kia Rio?
The engine control module is covered in the powertrain warranty for your Kia. The engine control module should be covered for 100,000 miles.
Where is the ignition control module on 1994 Ford Van E250 6 cylinder?
The only way I can explain it is to follow the wiring from your coil pack (where the spark plugs are) and the wires plug into the ignition module. Also go go www.wrenchead.ca and it has a manual that explains all. if you don't know the answer to a question please keep your moth shut ,please don't waste my time
Where can i get ignition control module for Mercedes Benz 300SE?
A Mercedes-Benz 300SE ignition control module can be obtained from most Mercedes-Benz dealerships. The ignition control module, can be purchased at most auto-parts stores.
What does the control module do on an electric scooter?
Controls the application of voltage to the motor to control speed and direction of the motor. If there is a built in charger it would also control the charging process.
Is the powertrain control module the same as the electric control module?
The powertrain control module is one of the electronic control modules used on a vehicle. Others include antilock brake, airbag, transmission, body,
How do you change the Ignition Control Module in a 1995 Blazer S-10?
Remove the wiring harness from your 1995 Chevy Blazer ignition control module. Remove the ignition control module retaining screws. Reverse the process to install your new ignition control module.
Where is the engine control module on 89 ford f-150 302?
wiring diagram
How do you install a electronic ignition control module?
The electronic ignition control module on an automobile is installed by first locating the unit at the top of the engine. The wiring harness is then disconnected from the original unit an a new module put in its place.
What does the comfort control module do in a 2000 VW passat?
As I know it is for electric windows, electric dooor locks and alarm. Might also control interior lights.
How do you replace HVAC control module on 01 Buick regal?
To replace the HVAC control module on a 2001 Buick Regal, first disconnect the negative battery cable to ensure safety. Remove the trim panel surrounding the HVAC controls, then unscrew and disconnect the old control module from its wiring harness. Install the new module by connecting the wiring harness and securing it with screws, then reattach the trim panel and reconnect the battery. Test the new module to ensure proper function.
Where you can find a wiring diagram of the Emission Module Control for an 84 Cadillac Coupe DeVille 4.1?
try MOTORLIT.COM
Can a touch lamp be converted to a regular electric lamp?
Yes, a touch lamp can be converted to a regular electric lamp by replacing the touch-sensitive module with a regular on/off switch. This involves disconnecting the touch control system and wiring in a traditional switch for manual control of the lamp.
How do you remove the ignition control module on 1990 Hyundai excel?
To remove the ignition control module from a 1990 Hyundai Excel, first disconnect the negative battery cable to ensure safety. Locate the ignition control module, which is typically mounted on the firewall or near the distributor. Unplug the wiring harness connected to the module and remove the mounting screws. Finally, carefully lift the module off its mounting brackets.
Where is the electric spark control module located on a 92 caprice?
on top of the right fenderwell next to the firewall
How do you replace a Transfer Case Control Module for a 2000 Chevy Blazer?
on your 2000 Blazer the control module is located under the kick panel on the passenger side. Simply remove the plastic panel, unbolt the module with a 10 MM socket and disconnect the wiring hareness. While your there, check the wiring hareness for corrosion as this is a big problem. apply Dielectric grease to the hareness and install new control module.
