If you're positive that it's teh ignition switch, the part is as low as $23 shipped - if you have a mechanic install it - he'll trouble shoot to make sure thats the part you need (being the problem), could cost you oup near $200 installed.
$109.99 item#IG23401 at schucks.com
In my case it was the ignition switch itself had overheated and seized up. Replace the switch (have to lower the column, disconnect the wiring plug from the switch, and remove/replace the switch.) Clean all connections to the switch, make sure they're connected solidly and not heating up again.
about how much does it cost to repair a car ignition tumbler
you can access the ignition switch from underneath the dash, but I found it easier to remove the steering wheel, then the instrument cluster. There are two basic elements to the ignition switch. The part that usually breaks down first is the front section, where the key goes into. You have to remove the entire unit from its bracket. Unplug the wire loom from the back of the housing. I believe there are two screws holding both sections together. Remove the screws and replace the unit. Then re-assemble. BUT FIRST, BEFORE YOU START TAKING EVERYTHING APART, TRY USING ANOTHER KEY. YOU'RE DEALING WITH A 25 YEAR OLD CAR, AND POSSIBLY A 25 YEAR OLD KEY (which I can't imagine, but its possible). YOU MIGHT ALSO WANT TO SQUIRT A SHOT OF WD-40 INTO THE IGNITION'S KEY SLOT...THERE COULD BE A STUCK SPRING OR BLADE INSIDE. If all that fails, then start taking the ignition switch apart. Its a fairly easy proceedure, less than 30 mins....and the switch should cost less than $60.00 from MB.
you need to replace your ignition in the steering column or take it apart and rebuild it. having a locksmith work on it might cost you less then replacing it though.
To replace an ignition switch on a Windstar, it will cost you approximately $200. This can also depend on the age of the vehicle as well.
$109.99 item#IG23401 at schucks.com
really that's not enough information. but, if your inquiring about a ford, there is a ignition switch (not to be confused with the key switch) on the top of the column. it is easy to replace and dosent cost alot for the switch.
It will cost between $300.00 to $500.00 to replace the rack and pinion on a 1996 Chrysler Sebring. This cost includes labor and parts.
The cost to replace the engine in your Chrysler Sebring will range between $2000 and $6000. Replacing with a used engine will be the cheapest and replacing with a brand-new engine will cost the most.
60.00 $
I had the Suby dealer in Auburn WA fix mine, the unit is held in place with 2 long bolts. The metal brackets are welded together and the electrical connections have to be soldered to the new Ignition switch. Cost-$289 or so.
It depends on what part of the country you live in. Call a couple of local garages for estimates.
The cost to replace a timing belt on a Chrysler Sebring can vary depending on the area you are in and if you do the job yourself or take it to a shop. You will have the cost of the belt and labor costs for the job if you take it to a shop.
In my case it was the ignition switch itself had overheated and seized up. Replace the switch (have to lower the column, disconnect the wiring plug from the switch, and remove/replace the switch.) Clean all connections to the switch, make sure they're connected solidly and not heating up again.
My experience with a faulty ignition switch on this generation Regal include random warning lights coming on together and turning off at the same time. Eventually, the car will sometimes stall when the turn signal switch is used. This is due to the turn signal switch "bumping" the wires leading into the ignition switch. Apparently, the wire connections inside the ignition switch sometimes tend to loosen. Dealer cost runs around $350 to $400 to replace.
It cost me 268.00 dollars today. The work was done by a local locksmith. My key would only go halfway into the barrel or switch.