Right, behind the cluster in a round rubber bung, remove this and you will see a 19mm hollow bolt. Get the wheel wrench as it is the right sized and undo the bolt. Then on the inside of the door post their are two bolts with slotted heads - remove these and the cluster will pull off.
took me days to work out
If it's the brake light in the boot lid then you have to take the cover off the inside of the boot lid and then you will have access to the light bulbs. If it's the brake light in the rear quarter panel then you open boot lid and unscrew the two bolts holding the light cluster and slide it backwards, then you will have access to the bulbs
Purchase a 12volt 21 Watt BA15s bulb, also marketed as a type 382. Refer to the owners/haynes manual and remove the relevant rear light cluster. The screws are accessed through the rear side panel. Remove the appropriate light fitting by twisting the holder a quarter turn counter-clockwise. Remove the bulb from the holder by pressing it in and turning it a quarter turn counter-clockwise. Replacement is the reverse of removal.
change the light bulb,
If none of them are working, then it will probably be a fuse as you probably won't have any running lights either. If not then, you need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.
means you have a problem in the rear brakes of your car. go to a mechanic before ya have a wreck
rear of van under neath bolt
To stop water from entering the rear light cluster on a Fiat Stilo 2002, first inspect the rubber seals and gaskets for any signs of wear or damage, as these are common entry points for moisture. Clean the area thoroughly and consider applying silicone sealant around the edges where the cluster meets the body. Additionally, check for any cracks in the light cluster itself and replace it if necessary. Finally, ensure that drainage holes are clear and functioning to prevent water buildup.
where can i get car nuts for cluster rear lights for fiat punto 51 year
To change the reversing light on a Fiat Punto Grande, first, ensure the vehicle is turned off and the keys are removed. Open the rear hatch and locate the light cluster; carefully remove the screws or clips holding it in place. Once the cluster is free, disconnect the electrical connector and twist the bulb holder counterclockwise to remove it. Replace the old bulb with a new one, reassemble the light cluster, and test the reversing lights to ensure they are functioning correctly.
To remove the rear light cluster on a Peugeot 3008, first, open the rear hatch and locate the access panel in the trunk area, typically on the side of the light cluster. Remove any screws or clips securing the panel, then disconnect the electrical connector from the light cluster. Once disconnected, you can unscrew or unclip the light cluster from the body of the vehicle and carefully pull it out. Replace it by reversing the steps.
Changing a Punto rear lampThere are two bolts to be unfastened to release the whole of the rear light cluster. The first is inside the car, just to the side above the top of the rear seat. The bolt can be unfastened using the plastic tool which is in in the boot with the spare wheel. Also, this bolt may be covered with a plastic clip, to match the vinyl at the rear of the car. The second bolt is hidden inside the boot; the 'carpet' in the boot may need to be pulled back near the rear light cluster. Once the two bolts have been removed (with care, don't drop them down the cavity), the rear light cluster can be removed. Next, unclip the plug to the light cluster so that it can be removed. Finally, unscrew the rear of the light cluster (four screws) and replace the bulb. This has to be the worst design ever and makes changing a lamp quite a hastle! .NickThere is a good video on YouTube how to do this:http://www.youtube.com/watch?v=0zsPZM-6DvM&list=UUe7_90E_rJSOeU92x1m7Wsw&index=6&feature=plcp
depends on the year on a 2005 you have to remove the rear cluster.
the left rear indicator light is only working intermitantly, how can this fault be rectified
To replace the rear light cluster unit on a Peugeot 307, first, open the rear hatch and remove the access panel in the trunk interior to expose the light cluster. Disconnect the electrical connector and unscrew the securing bolts of the light unit. Carefully pull the light cluster out and replace it with the new unit, reconnect the electrical connector, and secure it with the screws. Finally, test the lights to ensure everything is functioning properly before replacing the access panel.
open the tailgate ,and at the side of the light cluster you will find a small round pop out plastic disc, behind which is the release screw for the light cluster.
To change the rear lights on a Renault Scenic, start by opening the rear hatch and locating the access panel or screws securing the light cluster. Remove the screws or clips and gently pull the light cluster out from the body of the car. Disconnect the wiring harness and replace the burnt-out bulb by twisting it counterclockwise. Reassemble the light cluster by reversing the process and ensuring it is securely fitted.
open the boot you will find 3 screws undo them then ease the cluster away from body then remove the bulb cluster its easy to do