0
The abs light is on because there is a problem with your anti lock brake system. Until the problem is repaired the light will remain on. If you go to your local auto parts store they can read the code(s) and advise you as to what needs to be done. If you purchase the parts to make the repair from them they won't charge you for the diagnose. Once the repair is done the light will reset itself.
Wiki User
∙ 15y ago
Wiki User
∙ 17y agoBring to a shop that has and ABS scanner to note problem or clear codes
Wiki User
∙ 14y agoThe abs light is on because there is a problem with system. Until the problem is fixed the light will remain on.
Wiki User
∙ 15y agoYou need to have the code read with a scan tool, repair the cause, and clear the code with the scan tool.
Wiki User
∙ 11y agoAfter you fix the problem, the light will go out 2-3 starts later. If it stays on, you have not fixed the problem.
Add your answer:
Earn +20 pts
What is wrong when you rear abs and brake light sensor stays on in your 1995 rodeo?
you have a brake problem and need to have it repaired before you can reset the light sensor you have a brake problem and need to have it repaired before you can reset the light sensor
Where is the fuel pump reset switch and how do you activate it on a '94 Ford Ranger 4.0 V6 2-wheel drive truck?
It is about 18 inches up from the floor on the pass side of the cab. Find it and you will see how to reset it.
How would you reset the distributor computer on a 1995 Dodge Ram 1500 4X4 5.2L truck After replacing distributor on truck it now idles high and low and stalls?
If you have put the distributor back in the proper position and its not out a tooth you might try to disconnect the battery for a few minutes (5-10 to be safe) to reset the computer. I really think you're out by a tooth which has changed the timing though...
How do you fix the gas cap sensor on a 1999 Mercury Cougar?
my light went off when i put a new gas cap on and unhooked the battery 10 min too reset
Hi there you have a 1999 dodge ram diesel with bad tps throttle position sensor code p0123 I've replaced it but still when you push the throttle?
the code P0123 means, Throttle Position Sensor/Switch A Circuit High Input. sounds like a wiring problem to me. I had the same problem with a 99 Toyota tocoma when i replaced it i had to reset the CPU. On a dodge you should be able to disconnect both batteries for 15 mins to 1 hour and it mite reset.
Mazda truck b3000 where is the fuel pump reset switch loacted?
Mazda truck b3000 where is the fuel pump reset switch located
How do you reset the check engine light of Mazda bongo truck?
ODO
How do you reset the alarm system for a Mazda Truck?
Sit on it and count to 3.... FART!!!!!!!!
How do you reset sensor light on 1985 Nissan pickup truck?
The only way to reset the sensor light on a 1985 Nissan pickup truck is to disconnect the sensor wiring. After 60 seconds, put the wiring back in place.
How do you reset the check engine light on a 1989 Mazda MPV?
nothing but take it to Mazda and there computer will reset it, 1hr shop rate..100$ probably a sensor isn't working
How do you reset the tps ona 1992 Mazda protege throttle position sensor?
check the manual
Where is the inertial shut off switch for a 1998 Mazda B2500?
this is located on the passenger side kick panel remove the kick panel and you will see the switch it has a RED button on top press to reset.
How do you reset the 'check engine' light once an 02 Sensor has been replaced on a '95 Mazda Millenia?
you need an on board diagnostic scaner
How do you you reset change oil light on a Mazda?
Reset the change oil light on Mazda 3
Can You Reset computer on Mazda b2200?
How do you reset computer on 1989 Mazda B2200 PU truck? We seem to be having a key turn loop on computer and after so many starts the truck starts stalling out. Have cleaned computer 2 times now and problem seemed to go away but after similar time period usually a week the problem started again.
How do you do manual reset airbag light Mazda premacy?
how do i reset an airbag light on 2004 mazda premacy
How do you reset the oxygen sensor?
An Oxygen sensor does not reset. You have to replace them and yes they are expensive.
