0
It depends on the sprayer. Some you have to remove tfe tip and clear it with a small wire, others have a tip that reverses to clear clogs. Still others have a knob to increase the paint orifice, thereby allowing the clog to clear. if it's the machine itself, often tapping the pump area with a hammer works great.
Flush it out with the solvent you'd thin the paint sprayed; water for latex, mineral spirits for oil, until it is clear. If you plan to use the sprayer again within a couple of weeks, store it with mineral spirits in the system. If it's going to be longer than a couple of weeks, add some motor oil to the mineral spirits.
Flush out the material in the pump, hose and gun with the thinner specified for that material until it runs clean, then pump clean mineral spirits into the system through the gun at the lowest pressure possible. Store with mineral spirits up to two weeks, if longer storage is desired, use anti-freeze or an oil and mineral spirits blend instead of straight mineral spirits.
Add your answer:
Earn +20 pts
What kind of sprayer to use with Behr paint?
If you own a compressor, or plan on buying one, you will be looking for a general purpose sprayer that likely has the paint container sitting below the nozzle, since most gravity-fed sprayers (can above the nozzle) are for thin paints and varnishes used in automotive detailing applications. The important thing is to read the specifications for the sprayer to determine if latex paints can be used. Once you have found one or more that state they can be used with latex, ensure that the compressor you will be using has the required scf rating to deliver the latex paint through the sprayer. Some sprayers may require as little as 2 scf @ 40 psi which is something virtually every compressor can deliver while other latex-capable sprayers may require a more powerful compressor. Of course, you will also have to use a thinner in the latex paint regardless of the sprayer you choose. ANSWER: Actually, you can not use a cup gun to spray latex paint with a standard air compressor. The latex paint requires either a high amount of air or high pressure to atomize the paint. This can be done with an HVLP (High Volume Low Pressure) sprayer and gun, a gravity feed gun with a projector set that handles thicker fluids, or an airless paint sprayer that uses a piston or diaphragm to push the paint through a hose, to a gun where the paint will be atomized by a spray tip.
Airless Paint Sprayer?
Caution: An airless paint sprayer (mid to commercial grade) can inject large amounts of paint into your body if the spray is directed at the skin. Especially the arms and hands. This can result in serious injury including amputation and death if not immediately treated.Preparing the Surface:As with all painting, the surface to be painted should be thoroughly cleaned and dried. Any grime, mold or dirt will eventually come through the paint and leave the surface unseemly. Pressure washers can be implored for outdoor use. Preparing the Area:No matter how good you are at using a paint sprayer, there will be over spray. Over spray can get paint on other objects that were not meant to receive paint.Cover all plants and flooring with a drop clothCover windows with paper and tapePut tape on edges, such as trim, to prevent paint over spray (once you have mastered the use of the shield, you will not need to cover and tape everything)Preparing the SprayerTo get paint into the sprayer, put the inlet hose into a bucket of paint and turn on the sprayer. While the pump is on, pull the trigger on the gun until paint starts exiting the gun. There may be a specific sprayer function for priming the gun, like in the Graco XR7. Follow the manufacturer's instructions for priming or you could ruin your pump.Using the Paint SprayerPut on protective gear:Eye wear to protect eyes from over sprayGloves to prevent paint and over spray from staining hands, can also reduce the risk of accidental injection of paint through skinStart at the top left corner of the wall. In one hand, take the paint shield and place it against the closest wall or trim that will not be painted. With the other hand, point the paint sprayer gun at the wall in an upright 90 degree angle. Start moving the gun left to right and squeeze the trigger.Spray the paint on evenly by making a back and forth, left to right, right to left motion. If the paint begins to run, the paint is either to thin or you are spraying too much paint. Move the gun slightly faster to see if that reduces runs. You can also turn down the pressure of the paint gun.Clogged Paint Sprayer GunIf the paint gun becomes clogged, usually the tip can be reversed and automatically cleaned. To do this, simply turn the tip in reverse, point the gun away from your person and pull the trigger. The paint pressure will shoot any clogs out of the tip. If the tip still does not become usable, remove the tip and pour mineral spirits on both the entrance and exit spray holes. Take a wire brush and clean the paint off.AnswerGM929-Airless Paint Sprayer Description[1]1 2 3 4 5　1. Safety precautions2. Preparation3. Preparation before spraying4.Spraying instructions5. Turning off machine6. Cleaning, maintenance and storage7. Trouble shootings8. Other trouble shootings9. Paint sprayer assembly,Valve assembly,Spray gun assemblyChina airless paint sprayer manufacturer - Zhejiang Yongkang JeJar Spraying Equipment Factory welcome you! We are professional airless paint sprayer manufacturer and exporter in China. We can produce all kinds of high pressure airless paint sprayers according to your requirements. More types of high pressure airless paint sprayers wanted, please contact us right now!Ⅰ. Safety precautions1. As the airless paint sprayer is a high-pressure power tool, any inattention or improper operation, maintenance on your unit may result in equipment damage or severe personal injury. So before using your sprayer, make sure you read, fully understand, and will follow all the safety and operating instruc-tions given in this manual.2. Make sure the work area is in order, with no clutters, having sufficient visibility and be well ventila-ted.3. Make sure the sprayer and paint bucket is placed securely when working. Make sure all cords, extensions, and hoses are free from sharp objects.4. Always keep firm footing and balance when operating your sprayer. Take special care especially when you are working at heights (on scaffolding for example).5. Make sure the power source is securely grounded and match the motor rating of your sprayer. If an extension cord is needed, use one that is heavy enough, as an undersized cord will cause greater drop in line voltage causing loss of power and overheating.6. Before connecting your sprayer to power source, check hoses for cuts, leaks, abrasion or damage or movement of couplings, check all valves, controls and indicators to make sure they function proper-ly.7. Make sure the hydraulic oil in the pump is clean and sufficient in volume. Starting the sprayer with-out sufficient hydraulic oil is not permitted.8. To prevent earlier wear of the sprayer and even equipment failure, make sure paints and solvents to be used with the sprayer are clean and free from impurities.9. Watch for spraying pressure indicated in the pressure gauge, make sure it does not exceed 22.5-MPa. Make sure using the high pressure hose from supplier.10. Never aim the gun at any part of the body. Never allow any part of the body to come in contact with the fluid stream.11. Do not use this sprayer to spray any corrosive, or poisonous solvents (acids, banana oil, pestici-des, fertilizers etc.)12. Keep the sprayer free of ignition sources. Do not eat or smoke when operating.13. After each use, relieve pressure in the system before turning off the motor. Then clean the syste-m (all the parts paint having flowed through) with water or other appropriate solvents.14. Do not transport the sprayer with power on. Disconnect power source before cleaning or doing any maintenance. Do not have the motor and the plug come in contact with water, paints or solvents.15. Do not modify the sprayer in any way without approval. Use only original or authorized parts for replacement.Ⅱ. Preparation1. Attach the pressure gauge. (Fig.1)Fig. 12. Put the high pressure hose on the outlet valve, and input hose to the inlet valve, tighten them, then open the prime/spray valve.(fig2)Fig.2Copyright © 2005-2008 JeJar.Cn All Rights Reserved.Zhejiang Yongkang JeJar Spraying Equipment Factory浙ICP备05001021号Technical support: DotEb.Com1. Safety precautions2. Preparation3. Preparation before spraying4.Spraying instructions5. Turning off machine6. Cleaning, maintenance and storage7. Trouble shootings8. Other trouble shootings9. Paint sprayer assembly,Valve assembly,Spray gun assemblyChina airless paint sprayer manufacturer - Zhejiang Yongkang JeJar Spraying Equipment Factory welcome you! We are professional airless paint sprayer manufacturer and exporter in China. We can produce all kinds of high pressure airless paint sprayers according to your requirements. More types of high pressure airless paint sprayers wanted, please contact us right now!Ⅲ.Preparation before sprayingPut the inlet hose into the bucket with some water, turn on the motor and push the manual assistant valve repeatedly to help to suck liquor. In a few seconds, water will begin to flow up through the tube and flow out from outlet valve,close the outlet valve, check if there is any leakage on the outlet hose, if it doesn't leak, open the spraying gun and have a testing spray. (Fig.3)Fig. 3Ⅳ.Spraying instructions1.During paint spraying, hold the gun upright to the surface of paint-object and keep a constant spraying distance of 350~400mm.(Fig.4)2.Move gun before starting the trigger. Equably move gun when spraying. At last, loosen the trigger and stop moving immediately. Adjust moving speed according to thickness of paint, spray pressure and the distance of gun to object.3.In order to get an intact and slick surface, spray from level and vertical respectively . Spraying time will be variable with different paints. Spray for second time when the first painting is dry .Begin spraying on well spray stop spraying(Fig.4)4.During your spraying if you need to stop for several minutes, loosen the pressure valve and revolve prime valve in counter-clockwise, then shut the motor. Put spraying tip into solution in case of paint block-up in the spraying tip.When spraying tip is block-up, revolve it 180 degree for several times, then move back in position of well-spraying.1. Safety precautions2. Preparation3. Preparation before spraying4.Spraying instructions5. Turning off machine6. Cleaning, maintenance and storage7. Trouble shootings8. Other trouble shootings9. Paint sprayer assembly,Valve assembly,Spray gun assemblyChina airless paint sprayer manufacturer - Zhejiang Yongkang JeJar Spraying Equipment Factory welcome you! We are professional airless paint sprayer manufacturer and exporter in China. We can produce all kinds of high pressure airless paint sprayers according to your requirements. More types of high pressure airless paint sprayers wanted, please contact us right now!Ⅴ.Turning off machineAfter spraying, revolve pressure valve in counter-clockwise, loosen handle of prime valve, then shut the motor after the pressure gauge shows "0".Ⅵ.Cleaning, maintenance and storage1) After spraying, clean machine to avoid indurations and block-up. .2) Clean gun Filter after machine is used for some time. Discharge hose connector and hook plate, screw out gun handle, take out filter pistil and clean it, then fix them back. Change a new filter pistil when it is damaged. Wash the machine with relevant solvents for different paints.Fig.63) During spraying, check and clean suction-filter in time when paint blocks up. Usually clean it once after each use.4) To check timely if fixed parts are loosened and sealed parts have any leakage.5) Usually after three months' usage of the machine, open pump cover and check if hydraulic oil is clean and enough. Add hydraulic oil when it's in short; change hydraulic oil if it isn't clean. Clean oil-case of pump with diesel oil before changing hydraulic oil, and then add hydraulic oil to 85% of oil-case capacity.6) If you use this machine the second day, It is not necessary to clean it, dip the suction hose and tip into paint. For long storage, discharge the liquid in the machine, pack it well, store in dry and well-ventilated place, and don't be pressed by any articles.GM929-Airless Paint Sprayer Description[4]1 2 3 4 5　1. Safety precautions2. Preparation3. Preparation before spraying4.Spraying instructions5. Turning off machine6. Cleaning, maintenance and storage7. Trouble shootings8. Other trouble shootings9. Paint sprayer assembly,Valve assembly,Spray gun assemblyChina airless paint sprayer manufacturer - Zhejiang Yongkang JeJar Spraying Equipment Factory welcome you! We are professional airless paint sprayer manufacturer and exporter in China. We can produce all kinds of high pressure airless paint sprayers according to your requirements. More types of high pressure airless paint sprayers wanted, please contact us right now!Ⅶ.Trouble shootingsThe normal problems for machine are:1)The machine doesn't absorb liquid.2)It doesn't spray.Please try the following solution:1)Check if Inlet valve is in stickiness or leakage. If inlet valve is sticky, refer to fig.1. Push the dustpr-oof plug inside the inlet valve. To fill water into inlet valve and check whether it's leaky. If it's leaky, contact supplier to change it.Fig.72)Check whether the diaphragm is damaged. If it is damaged, oil goes out from outlet hose when it absorbs liquid, in additional, check if there is any hydraulic oil in the pump.Put this machine backward, loosen four fixed bolts on valve assembly, remove them and take out diaphragm to change.It's necessary to discharge air after changing diaphragm. Please follow these steps: Unscrew copper nut of pressure valve, turn on the motor repeatedly till air is out. To check if the air is released, tighten copper nut of pressure valve, remove inlet valve and extend finger into the center hole of inlet valve, gently touch the diaphragm, if you can feel it's vibrating, it means there is no air inside Otherwise, repeat the above.Fig.8Ⅷ.Other trouble shootings1.If the prime valve is leaky, circumfluence accrues in outlet hose when the valve is closed.1). Open and close spray valve in times to check whether inner parts of spray valve are locked.2).Discharge spray valve to check whether it is damaged. Take out gasket to inspect if the surface of it and hole bottom of spray valve are smooth. Change gasket if it isn't good. Contact supplier to maintain if hole bottom of spray vale isn't good. (Fig.9)2.Leakage between valve assembly and pump1)Check if the four bolts are loosening.2)Change valve assembly if seal grains behind it are damaged.(Fig.10)Fig.9Fig.103. Contact the manufacturer if oil leakage in motor occurs, no hydraulic oil in pump or motor doesn't work.GM929 Airless Paint Sprayer Description[5]1 2 3 4 5　1. Safety precautions2. Preparation3. Preparation before spraying4.Spraying instructions5. Turning off machine6. Cleaning, maintenance and storage7. Trouble shootings8. Other trouble shootings9. Paint sprayer assembly,Valve assembly,Spray gun assemblyChina airless paint sprayer manufacturer - Zhejiang Yongkang JeJar Spraying Equipment Factory welcome you! We are professional airless paint sprayer manufacturer and exporter in China. We can produce all kinds of high pressure airless paint sprayers according to your requirements. More types of high pressure airless paint sprayers wanted, please contact us right now!Ⅸ.Paint sprayer assembly, Valve assembly, Spray gun assemblyFig.11 Exploded parts view and parts list (The whole unit)NO.DESCRIPTIONQ'TYNO.DESCRIPTIONQ'TY1Gun16Inlet hose12Hydraulic pump17Outlet hose13Valve assembly18Filter14Pressure valve19Flame15Motor110Handle1Fig.12 The valve assemblyNO.DESCRIPTIONQ'TYNO.DESCRIPTIONQ'TY11Outlet valve115Manual assistant valve112Plastic packer116Inlet valve113Prime/spray valve117Pressure gauge114Connector of outlet hose118Valve block1Fig.13 The gunAnswerUSUALLY YOU SHOULD PROBABLY LEAVE SPRAYING TO THE PROFESSIONALS. A TYPICAL PERSON THAT DOESNT KNOW WHAT TO DO CAN DO MAJOR DAMAGE TO THEIR HOME AND THEMSELVES. PLUS YOUR STILL GOING TO HAVE TO HIRE A PROFESSIONAL TO FIX YOUR MISTAKES. DONT LET LOWES AND HOME DEPOT FOOL YOU THEY JUST WANT YOUR MONEY. never under estimate over spray!!
How do you use a Graco RTX 1500 paint sprayer?
Put pick up tube in material. Flip black plastic drain valve handle down to open position. Turn sprayer on and run until material flow from smaller prime hose. Turn off sprayer, set pressure with pressure control knob, clock for pres. up. Flip drain valve handle back up to closed position. Turn machine on, let it build pres until motor stops. Fire away. If paint flow suddenly stops at the gun, turn spray tip handle half turn count clock, trigger gun to clear tip clog, reverse back to spray position and continue.
How do you repair wiper arm for 2001 intrigue?
Wiper arms cannot be repaired, only replaced. The arm should come off by removing the nut at the bottom of the arm and the washer sprayer hose
Why is an earth wire incorporated in an airless spray material hose?
Because when paint passes through the tip of an airless sprayer it builds a static charge. When spraying an oil, this could cause a spark on an ungrounded system which could in turn, cause a fire. Gas airless sprayers have a wire that needs to be attached to a ground prior to use. Electric airlesses must have the ground plug present whenever material is being sprayed.
What kind of sprayer to use with Behr paint?
If you own a compressor, or plan on buying one, you will be looking for a general purpose sprayer that likely has the paint container sitting below the nozzle, since most gravity-fed sprayers (can above the nozzle) are for thin paints and varnishes used in automotive detailing applications. The important thing is to read the specifications for the sprayer to determine if latex paints can be used. Once you have found one or more that state they can be used with latex, ensure that the compressor you will be using has the required scf rating to deliver the latex paint through the sprayer. Some sprayers may require as little as 2 scf @ 40 psi which is something virtually every compressor can deliver while other latex-capable sprayers may require a more powerful compressor. Of course, you will also have to use a thinner in the latex paint regardless of the sprayer you choose. ANSWER: Actually, you can not use a cup gun to spray latex paint with a standard air compressor. The latex paint requires either a high amount of air or high pressure to atomize the paint. This can be done with an HVLP (High Volume Low Pressure) sprayer and gun, a gravity feed gun with a projector set that handles thicker fluids, or an airless paint sprayer that uses a piston or diaphragm to push the paint through a hose, to a gun where the paint will be atomized by a spray tip.
How do you clean a ball python?
Water. You can let the snake soak, or you can spray it down with some water (not a hose, a handheld sprayer). You can rub the snake gently also.
How do you remove green algae from painted exterior walls of house?
Paint with bleach and then clean with high pressure hose
How do you clean a home air conditioning filter?
most are washable by simply rinsing. use a spray rinse such as a kitchen sprayer. you can use your garden hose if you are very careful not to spray too forcefully
Can you disconnect the sprayer and still use the faucet?
If the sprayer hose screws onto the faucet, you can get a cap for that fitting. If it pushes into the faucet, I do not believe there is any plug available for that type. You have to have something on the hose fitting or water will come out when you turn the faucet on.
How do you fix the wiper hose to the sprayers 2006 Dodge Charger they froze this winter and broke at the sprayer under the hood.?
see if you can pull more hose up to the sprayers and cut off the section of hose that is broken and then re-attach the hose.
How do you clean paving?
witha a hose witha a hose
How do you connect a water purification system to the sink sprayer hose?
You cannot do this without a way of stopping the water. The sink sprayer is hooked up through your kitchen faucet for a reason. When the faucet is shut off, no water can come through the sprayer. If you hook up the sprayer to a water filter, the handle on the sprayer cannot handle the pressure of the water system and will continually run when the handle packs it in, more than likely when you are not home!
Can you add a sink sprayer to any kitchen faucet?
No, they have to have a place to attach it. The fitting is in the middle of the faucet underneath directly under the spout.You can also add on a hose sprayer to end of the faucet but you need a special fitting to do this. The fitting needs to be adapted with a quick release. A replacement sprayer with hose is then attached to this fitting along with the quick release. You then attached the whole unit to the end of the faucet. Neat part is that if you move you can take it with you.
Airless Paint Sprayer?
Caution: An airless paint sprayer (mid to commercial grade) can inject large amounts of paint into your body if the spray is directed at the skin. Especially the arms and hands. This can result in serious injury including amputation and death if not immediately treated.Preparing the Surface:As with all painting, the surface to be painted should be thoroughly cleaned and dried. Any grime, mold or dirt will eventually come through the paint and leave the surface unseemly. Pressure washers can be implored for outdoor use. Preparing the Area:No matter how good you are at using a paint sprayer, there will be over spray. Over spray can get paint on other objects that were not meant to receive paint.Cover all plants and flooring with a drop clothCover windows with paper and tapePut tape on edges, such as trim, to prevent paint over spray (once you have mastered the use of the shield, you will not need to cover and tape everything)Preparing the SprayerTo get paint into the sprayer, put the inlet hose into a bucket of paint and turn on the sprayer. While the pump is on, pull the trigger on the gun until paint starts exiting the gun. There may be a specific sprayer function for priming the gun, like in the Graco XR7. Follow the manufacturer's instructions for priming or you could ruin your pump.Using the Paint SprayerPut on protective gear:Eye wear to protect eyes from over sprayGloves to prevent paint and over spray from staining hands, can also reduce the risk of accidental injection of paint through skinStart at the top left corner of the wall. In one hand, take the paint shield and place it against the closest wall or trim that will not be painted. With the other hand, point the paint sprayer gun at the wall in an upright 90 degree angle. Start moving the gun left to right and squeeze the trigger.Spray the paint on evenly by making a back and forth, left to right, right to left motion. If the paint begins to run, the paint is either to thin or you are spraying too much paint. Move the gun slightly faster to see if that reduces runs. You can also turn down the pressure of the paint gun.Clogged Paint Sprayer GunIf the paint gun becomes clogged, usually the tip can be reversed and automatically cleaned. To do this, simply turn the tip in reverse, point the gun away from your person and pull the trigger. The paint pressure will shoot any clogs out of the tip. If the tip still does not become usable, remove the tip and pour mineral spirits on both the entrance and exit spray holes. Take a wire brush and clean the paint off.AnswerGM929-Airless Paint Sprayer Description[1]1 2 3 4 5　1. Safety precautions2. Preparation3. Preparation before spraying4.Spraying instructions5. Turning off machine6. Cleaning, maintenance and storage7. Trouble shootings8. Other trouble shootings9. Paint sprayer assembly,Valve assembly,Spray gun assemblyChina airless paint sprayer manufacturer - Zhejiang Yongkang JeJar Spraying Equipment Factory welcome you! We are professional airless paint sprayer manufacturer and exporter in China. We can produce all kinds of high pressure airless paint sprayers according to your requirements. More types of high pressure airless paint sprayers wanted, please contact us right now!Ⅰ. Safety precautions1. As the airless paint sprayer is a high-pressure power tool, any inattention or improper operation, maintenance on your unit may result in equipment damage or severe personal injury. So before using your sprayer, make sure you read, fully understand, and will follow all the safety and operating instruc-tions given in this manual.2. Make sure the work area is in order, with no clutters, having sufficient visibility and be well ventila-ted.3. Make sure the sprayer and paint bucket is placed securely when working. Make sure all cords, extensions, and hoses are free from sharp objects.4. Always keep firm footing and balance when operating your sprayer. Take special care especially when you are working at heights (on scaffolding for example).5. Make sure the power source is securely grounded and match the motor rating of your sprayer. If an extension cord is needed, use one that is heavy enough, as an undersized cord will cause greater drop in line voltage causing loss of power and overheating.6. Before connecting your sprayer to power source, check hoses for cuts, leaks, abrasion or damage or movement of couplings, check all valves, controls and indicators to make sure they function proper-ly.7. Make sure the hydraulic oil in the pump is clean and sufficient in volume. Starting the sprayer with-out sufficient hydraulic oil is not permitted.8. To prevent earlier wear of the sprayer and even equipment failure, make sure paints and solvents to be used with the sprayer are clean and free from impurities.9. Watch for spraying pressure indicated in the pressure gauge, make sure it does not exceed 22.5-MPa. Make sure using the high pressure hose from supplier.10. Never aim the gun at any part of the body. Never allow any part of the body to come in contact with the fluid stream.11. Do not use this sprayer to spray any corrosive, or poisonous solvents (acids, banana oil, pestici-des, fertilizers etc.)12. Keep the sprayer free of ignition sources. Do not eat or smoke when operating.13. After each use, relieve pressure in the system before turning off the motor. Then clean the syste-m (all the parts paint having flowed through) with water or other appropriate solvents.14. Do not transport the sprayer with power on. Disconnect power source before cleaning or doing any maintenance. Do not have the motor and the plug come in contact with water, paints or solvents.15. Do not modify the sprayer in any way without approval. Use only original or authorized parts for replacement.Ⅱ. Preparation1. Attach the pressure gauge. (Fig.1)Fig. 12. Put the high pressure hose on the outlet valve, and input hose to the inlet valve, tighten them, then open the prime/spray valve.(fig2)Fig.2Copyright © 2005-2008 JeJar.Cn All Rights Reserved.Zhejiang Yongkang JeJar Spraying Equipment Factory浙ICP备05001021号Technical support: DotEb.Com1. Safety precautions2. Preparation3. Preparation before spraying4.Spraying instructions5. Turning off machine6. Cleaning, maintenance and storage7. Trouble shootings8. Other trouble shootings9. Paint sprayer assembly,Valve assembly,Spray gun assemblyChina airless paint sprayer manufacturer - Zhejiang Yongkang JeJar Spraying Equipment Factory welcome you! We are professional airless paint sprayer manufacturer and exporter in China. We can produce all kinds of high pressure airless paint sprayers according to your requirements. More types of high pressure airless paint sprayers wanted, please contact us right now!Ⅲ.Preparation before sprayingPut the inlet hose into the bucket with some water, turn on the motor and push the manual assistant valve repeatedly to help to suck liquor. In a few seconds, water will begin to flow up through the tube and flow out from outlet valve,close the outlet valve, check if there is any leakage on the outlet hose, if it doesn't leak, open the spraying gun and have a testing spray. (Fig.3)Fig. 3Ⅳ.Spraying instructions1.During paint spraying, hold the gun upright to the surface of paint-object and keep a constant spraying distance of 350~400mm.(Fig.4)2.Move gun before starting the trigger. Equably move gun when spraying. At last, loosen the trigger and stop moving immediately. Adjust moving speed according to thickness of paint, spray pressure and the distance of gun to object.3.In order to get an intact and slick surface, spray from level and vertical respectively . Spraying time will be variable with different paints. Spray for second time when the first painting is dry .Begin spraying on well spray stop spraying(Fig.4)4.During your spraying if you need to stop for several minutes, loosen the pressure valve and revolve prime valve in counter-clockwise, then shut the motor. Put spraying tip into solution in case of paint block-up in the spraying tip.When spraying tip is block-up, revolve it 180 degree for several times, then move back in position of well-spraying.1. Safety precautions2. Preparation3. Preparation before spraying4.Spraying instructions5. Turning off machine6. Cleaning, maintenance and storage7. Trouble shootings8. Other trouble shootings9. Paint sprayer assembly,Valve assembly,Spray gun assemblyChina airless paint sprayer manufacturer - Zhejiang Yongkang JeJar Spraying Equipment Factory welcome you! We are professional airless paint sprayer manufacturer and exporter in China. We can produce all kinds of high pressure airless paint sprayers according to your requirements. More types of high pressure airless paint sprayers wanted, please contact us right now!Ⅴ.Turning off machineAfter spraying, revolve pressure valve in counter-clockwise, loosen handle of prime valve, then shut the motor after the pressure gauge shows "0".Ⅵ.Cleaning, maintenance and storage1) After spraying, clean machine to avoid indurations and block-up. .2) Clean gun Filter after machine is used for some time. Discharge hose connector and hook plate, screw out gun handle, take out filter pistil and clean it, then fix them back. Change a new filter pistil when it is damaged. Wash the machine with relevant solvents for different paints.Fig.63) During spraying, check and clean suction-filter in time when paint blocks up. Usually clean it once after each use.4) To check timely if fixed parts are loosened and sealed parts have any leakage.5) Usually after three months' usage of the machine, open pump cover and check if hydraulic oil is clean and enough. Add hydraulic oil when it's in short; change hydraulic oil if it isn't clean. Clean oil-case of pump with diesel oil before changing hydraulic oil, and then add hydraulic oil to 85% of oil-case capacity.6) If you use this machine the second day, It is not necessary to clean it, dip the suction hose and tip into paint. For long storage, discharge the liquid in the machine, pack it well, store in dry and well-ventilated place, and don't be pressed by any articles.GM929-Airless Paint Sprayer Description[4]1 2 3 4 5　1. Safety precautions2. Preparation3. Preparation before spraying4.Spraying instructions5. Turning off machine6. Cleaning, maintenance and storage7. Trouble shootings8. Other trouble shootings9. Paint sprayer assembly,Valve assembly,Spray gun assemblyChina airless paint sprayer manufacturer - Zhejiang Yongkang JeJar Spraying Equipment Factory welcome you! We are professional airless paint sprayer manufacturer and exporter in China. We can produce all kinds of high pressure airless paint sprayers according to your requirements. More types of high pressure airless paint sprayers wanted, please contact us right now!Ⅶ.Trouble shootingsThe normal problems for machine are:1)The machine doesn't absorb liquid.2)It doesn't spray.Please try the following solution:1)Check if Inlet valve is in stickiness or leakage. If inlet valve is sticky, refer to fig.1. Push the dustpr-oof plug inside the inlet valve. To fill water into inlet valve and check whether it's leaky. If it's leaky, contact supplier to change it.Fig.72)Check whether the diaphragm is damaged. If it is damaged, oil goes out from outlet hose when it absorbs liquid, in additional, check if there is any hydraulic oil in the pump.Put this machine backward, loosen four fixed bolts on valve assembly, remove them and take out diaphragm to change.It's necessary to discharge air after changing diaphragm. Please follow these steps: Unscrew copper nut of pressure valve, turn on the motor repeatedly till air is out. To check if the air is released, tighten copper nut of pressure valve, remove inlet valve and extend finger into the center hole of inlet valve, gently touch the diaphragm, if you can feel it's vibrating, it means there is no air inside Otherwise, repeat the above.Fig.8Ⅷ.Other trouble shootings1.If the prime valve is leaky, circumfluence accrues in outlet hose when the valve is closed.1). Open and close spray valve in times to check whether inner parts of spray valve are locked.2).Discharge spray valve to check whether it is damaged. Take out gasket to inspect if the surface of it and hole bottom of spray valve are smooth. Change gasket if it isn't good. Contact supplier to maintain if hole bottom of spray vale isn't good. (Fig.9)2.Leakage between valve assembly and pump1)Check if the four bolts are loosening.2)Change valve assembly if seal grains behind it are damaged.(Fig.10)Fig.9Fig.103. Contact the manufacturer if oil leakage in motor occurs, no hydraulic oil in pump or motor doesn't work.GM929 Airless Paint Sprayer Description[5]1 2 3 4 5　1. Safety precautions2. Preparation3. Preparation before spraying4.Spraying instructions5. Turning off machine6. Cleaning, maintenance and storage7. Trouble shootings8. Other trouble shootings9. Paint sprayer assembly,Valve assembly,Spray gun assemblyChina airless paint sprayer manufacturer - Zhejiang Yongkang JeJar Spraying Equipment Factory welcome you! We are professional airless paint sprayer manufacturer and exporter in China. We can produce all kinds of high pressure airless paint sprayers according to your requirements. More types of high pressure airless paint sprayers wanted, please contact us right now!Ⅸ.Paint sprayer assembly, Valve assembly, Spray gun assemblyFig.11 Exploded parts view and parts list (The whole unit)NO.DESCRIPTIONQ'TYNO.DESCRIPTIONQ'TY1Gun16Inlet hose12Hydraulic pump17Outlet hose13Valve assembly18Filter14Pressure valve19Flame15Motor110Handle1Fig.12 The valve assemblyNO.DESCRIPTIONQ'TYNO.DESCRIPTIONQ'TY11Outlet valve115Manual assistant valve112Plastic packer116Inlet valve113Prime/spray valve117Pressure gauge114Connector of outlet hose118Valve block1Fig.13 The gunAnswerUSUALLY YOU SHOULD PROBABLY LEAVE SPRAYING TO THE PROFESSIONALS. A TYPICAL PERSON THAT DOESNT KNOW WHAT TO DO CAN DO MAJOR DAMAGE TO THEIR HOME AND THEMSELVES. PLUS YOUR STILL GOING TO HAVE TO HIRE A PROFESSIONAL TO FIX YOUR MISTAKES. DONT LET LOWES AND HOME DEPOT FOOL YOU THEY JUST WANT YOUR MONEY. never under estimate over spray!!
How do you change the rear window washer sprayer for a 2004 Acura MDX?
Open tailgate and pry plastic panel behind tailgate light. Pop out the old sprayer and disconnect the hose and pop in the new one. Very simple.
How do you clean a chihuahua?
If its calm you can clean it in the bathtub or if it moves lot you can clean it with a hose.
