0
Add your answer:
Earn +20 pts
Where can you get direction to replace upper and lower ball joints on your 2005 dodge ram disiel 2500 pickup?
Replacing ball joints is very labor intensive, and should not be done at home if you are not experienced at auto repair. A very quick generalized rundown of the procedure is: Raise and support vehicle Remove wheel Remove tie rod nut Separate tie rod from knuckle Remove brake caliper and rotor Remove front axle nut(on 4X4 models) Remove or unplug ABS sensor if equipped Support lower control arm with jack Remove upper ball joint nut Separate upper ball joint Remove lower ball joint nut Separate lower ball joint Remove steering knuckle assembly with hub and all from vehicle. Use ball joint press to remove and replace ball joints. Reverse procedure to put car back together. Repeat for other side.
Does eating almonds cause joint pain?
No, eating almonds is a good thing to do if you have problems with joint pain or arthritis.
Is it unsafe to drive a jeep with bad ball joints?
A bad ball joint isn't safe any way you look at it. Some major damage can happen if the wheel becomes dislodged from the chassis. The major component holding the wheels on are the ball joints, upper and lower, which hold the spindle that houses the axle. The spindle holds the wheel bearing, tie rod, brakes, wheel etc. You can lift the vehicle up by the front and check the wheel for play, up and down. There shouldn't be much, if any play. If there is alot of play then you shouldn't drive it much till it get's fixed. That's my opinion. Good luck.
How do you fix hole in exhaust between catconverter and muffler?
If the pipe is in good enough shape you can weld over the hole, BUT If there is one small hole rusted in the system it is a good sign the pipe is rotted. There will be many other holes soon. There are probably more holes than you know about. You will probably have to have an exhaust shop put in a new pipe for you.
What object is a good model of earth in terms of roundness?
and blue and green super boncey ball ^_^
How do you remove the lower ball joint on a 1989 Honda Civic?
I recently removed the lower ball joint from a 91 Civic, hopefully it is the same as yours. You need a fairly large double jaw gear puller. Loosen the castle nut, but do not remove it. Place the jaws of the gear puller under the boot of the ball joint (be careful not to damage the boot). Then place the screw part of the puller on the end of the ball joint bolt and tighten the puller as tight as you possible can. Then use a blunt punch and hammer to hit on the lower arm where the bolt goes through it, it requires quite a vibration to jar the ball joint loose. Good luck.
Remove ball joint 1997 GMC?
Ball Joint Replacement: I used the rental tool to press out the old ball joint and press in the new one. When pressing out the old ball joint the key is to properly set up the press, tighten the screw on the press, then give the screw a few good solid blows to shock the old ball joint. Once I did this the old ball joint pressed out almost effortlessly. Installation of the new ball joint was a breeze. The only comment is be extremely careful not to damage the axle boot seals. Have wire on hand to tie the spindle assembly and axle for support to prevent damage to the brake hoses and ABS system.
How do you change a lower ball joint on a 99 impala?
Ball Joint Replacement: I used the rental tool to press out the old ball joint and press in the new one. When pressing out the old ball joint the key is to properly set up the press, tighten the screw on the press, then give the screw a few good solid blows to shock the old ball joint. Once I did this the old ball joint pressed out almost effortlessly. Installation of the new ball joint was a breeze. The only comment is be extremely careful not to damage the axle boot seals. Have wire on hand to tie the spindle assembly and axle for support to prevent damage to the brake hoses and ABS system.
Ball joint removal 1996 F150?
Ball Joint Replacement: I used the rental tool to press out the old ball joint and press in the new one. When pressing out the old ball joint the key is to properly set up the press, tighten the screw on the press, then give the screw a few good solid blows to shock the old ball joint. Once I did this the old ball joint pressed out almost effortlessly. Installation of the new ball joint was a breeze. The only comment is be extremely careful not to damage the axle boot seals. Have wire on hand to tie the spindle assembly and axle for support to prevent damage to the brake hoses and ABS system.
Does the lower ball joint have to be pressed on?
Ball Joint Replacement: I used the rental tool to press out the old ball joint and press in the new one. When pressing out the old ball joint the key is to properly set up the press, tighten the screw on the press, then give the screw a few good solid blows to shock the old ball joint. Once I did this the old ball joint pressed out almost effortlessly. Installation of the new ball joint was a breeze. The only comment is be extremely careful not to damage the axle boot seals. Have wire on hand to tie the spindle assembly and axle for support to prevent damage to the brake hoses and ABS system.
Ball joint on Toyota Tacoma?
Ball Joint Replacement: I used the rental tool to press out the old ball joint and press in the new one. When pressing out the old ball joint the key is to properly set up the press, tighten the screw on the press, then give the screw a few good solid blows to shock the old ball joint. Once I did this the old ball joint pressed out almost effortlessly. Installation of the new ball joint was a breeze. The only comment is be extremely careful not to damage the axle boot seals. Have wire on hand to tie the spindle assembly and axle for support to prevent damage to the brake hoses and ABS system.
1985 Ford f150 pickup truck ball joint replacement?
Ball Joint Replacement: I used the rental tool to press out the old ball joint and press in the new one. When pressing out the old ball joint the key is to properly set up the press, tighten the screw on the press, then give the screw a few good solid blows to shock the old ball joint. Once I did this the old ball joint pressed out almost effortlessly. Installation of the new ball joint was a breeze. The only comment is be extremely careful not to damage the axle boot seals. Have wire on hand to tie the spindle assembly and axle for support to prevent damage to the brake hoses and ABS system.
Ball joints on 1993 ford f-150?
Ball Joint Replacement: I used the rental tool to press out the old ball joint and press in the new one. When pressing out the old ball joint the key is to properly set up the press, tighten the screw on the press, then give the screw a few good solid blows to shock the old ball joint. Once I did this the old ball joint pressed out almost effortlessly. Installation of the new ball joint was a breeze. The only comment is be extremely careful not to damage the axle boot seals. Have wire on hand to tie the spindle assembly and axle for support to prevent damage to the brake hoses and ABS system.
Remove and replace ball-joints on 2000 ford expedition?
Ball Joint Replacement: I used the rental tool to press out the old ball joint and press in the new one. When pressing out the old ball joint the key is to properly set up the press, tighten the screw on the press, then give the screw a few good solid blows to shock the old ball joint. Once I did this the old ball joint pressed out almost effortlessly. Installation of the new ball joint was a breeze. The only comment is be extremely careful not to damage the axle boot seals. Have wire on hand to tie the spindle assembly and axle for support to prevent damage to the brake hoses and ABS system.
How to change lower ball joints 2002 Lincoln Navigator?
Ball Joint Replacement: I used the rental tool to press out the old ball joint and press in the new one. When pressing out the old ball joint the key is to properly set up the press, tighten the screw on the press, then give the screw a few good solid blows to shock the old ball joint. Once I did this the old ball joint pressed out almost effortlessly. Installation of the new ball joint was a breeze. The only comment is be extremely careful not to damage the axle boot seals. Have wire on hand to tie the spindle assembly and axle for support to prevent damage to the brake hoses and ABS system.
How do you change a ball joint on 99 Mazda millenia?
you need a good ball joint separator. if you use a pickle fork, you will destroy the boot. so, if you are going to reuse the joint, you will have to use the screw in type. once you separate the ball joint, then it bolts to the control arm with 3 bolts. first, pull the wheel. to be safe, unbolt the brackets that hold the brake hose, and remove the abs sensor and tie it up. remove the brake caliper, and tie up out of the way. disconnect the sway bar link. remove brake rotor for clearance. i always break loose the bolts on the bottom of the ball joint before i disconnect the ball joint
How do you change upper and lower ball joints on a 1998 ford f-150?
Ball Joint Replacement: I used the rental tool to press out the old ball joint and press in the new one. When pressing out the old ball joint the key is to properly set up the press, tighten the screw on the press, then give the screw a few good solid blows to shock the old ball joint. Once I did this the old ball joint pressed out almost effortlessly. Installation of the new ball joint was a breeze. The only comment is be extremely careful not to damage the axle boot seals. Have wire on hand to tie the spindle assembly and axle for support to prevent damage to the brake hoses and ABS system.
